- 您現在的位置：買賣IC網 > PDF目錄2080 > ISL24202IRTZ (Intersil)IC PROG 8BIT VCOM CALIBRTR 8TDFN PDF資料下載
參數資料
| 型號： | ISL24202IRTZ |
| 廠商： | Intersil |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PROG 8BIT VCOM CALIBRTR 8TDFN |
| 標準包裝： | 100 |
| 類型： | 校準器 |
| 應用： | LCD 驅動器，基準電壓發生器 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-WDFN 裸露焊盤 |
| 供應商設備封裝： | 8-TDFN（3x3） |
| 包裝： | 管件 |
ISL24202
8
FN7587.0
March 15, 2011
Assuming that the IOUT(MIN) = 0 instead of ISTEP, the expression
in Equation 14 simplifies to:
OUT Pin Leakage Current
When the voltage on the OUT pin is greater than 10V, an
additional leakage current flows into the pin in addition to the
current for OUT pin voltage up to 19V. In applications where the
voltage on the OUT pin will be greater than 10V, the actual output
voltage will be lower than the voltage calculated by Equation 8
due to this extra current. The graph in Figure 6 was measured
with RSET = 4.99kΩ.
Power Supply Sequence
The recommended power supply sequencing is shown in
at the same time as AVDD. The minimum time for tVS is 0s.
When removing power, the sequence of VDD and AVDD is not
important.
Do not remove VDD or AVDD within 100ms of the start of the
EEPROM programming cycle. Removing power before the
EEPROM programming cycle is completed may result in
corrupted data in the EEPROM.
Operating and Programming
Supply Voltage and Current
To program the EEPROM, AVDD must be ≥10.8V. If further
programming is not required, the ISL24202 will operate over an
AVDD range of 4.5V to 19V.
During EEPROM programming, IDD and IAVDD will temporarily be
4-5x higher for up to 100ms (tPROG).
Up/Down Counter Interface
The ISL24202 allows the adjustment of the output VCOM voltage
and the programming of the non-volatile memory through a
single pin (CTL) when the CE (counter enable) pin is high. The CTL
pin is biased so that its voltage is set to VDD/2 if the driving
circuit is set to Tri-state or High Impedance (Hi-Z), allowing
up/down operation using common digital I/O logic.
CTL Pin
When a mid-high-mid transition is detected on the CTL pin (see
Figure 11), the internal register value counts down by one at the
trailing (high-mid) edge, and the output VCOM voltage is
increased according to Equation 8. Similarly, when a mid-low-mid
transition is detected on the CTL pin, the internal register value
counts up by one at the trailing (low-mid) edge, and the output
VCOM voltage is decreased. Once the maximum or minimum
value is reached, the counter saturates and will not overflow or
underflow beyond those values.
CTL should have a noise filter to reduce bouncing or noise on the
input that could cause unwanted counts when the CE pin is high.
Figure 8 shows a simple debouncing circuit consisting of a series
1k
Ω resistor and a shunt 0.01F capacitor connected on the CTL
pin. To avoid unintentional adjustment, the ISL24202 guarantees
to reject CTL pulses shorter than 20s.
This pin is pulled above 4.9V to program the EEPROM. See
“Programming the EEPROM” on page 9 for details.
After CE (Counter Enable) is asserted and after programming
EEPROM, the very first CTL pulse is ignored (see Figure 11) to
avoid the possibility of a false count (since CTL state may be
unknown after programming).
CE Pin
To change the counter controlling the output voltage, the CE
(Counter Enable) pin must be pulled high (VDD). When the CE pin
is pulled low, the counter value is loaded from EEPROM, which
takes 10ms (during which the inputs should remain constant).
The CE pin has an internal pull-down to keep it at a logic low
VCOMSPAN
R1 R
2
R1 R2
+
--------------------
AVDD
20RSET
--------------------
R1 R
2
R1 R2
+
--------------------
IDVROUT MAX
()
==
(EQ. 15)
FIGURE 6. OUT PIN LEAKAGE CURRENT
0
2468
10
12
14
16
18
20
OUT PIN VOLTAGE (V)
CURRENT
(
m
A)
0.00
0.05
0.10
0.15
0.20
0.25
0.30
OUT PIN CURRENT
SET PIN CURRENT
REGISTER = 255
VDD
AVDD
tVS
FIGURE 7. POWER SUPPLY SEQUENCE
FIGURE 8. EXTERNAL DEBOUNCER ON CTL PIN
ISL24202
CTL
0.01F
1k
Ω
AVDD
CLOSE TO
EEPROM
PROGRAM
相關PDF資料 |
PDF描述 |
|---|---|
| ISL24211IRTZ | IC VCOM CALIBRATOR I2C 10TDFN |
| ISL24212IRTZ | IC PROG 8BIT VCOM CALIBRTR 10TDF |
| ISL28197FRUZ-T7 | IC COMP RRIO SGL 800NA 6-TDFN |
| ISL3035EIRTZ-T | IC LEVEL TRANSLATOR 6CH 16-TQFN |
| ISL4089IBZ-T7A | IC VIDEO AMP DC-RESTORED 8SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL24202IRTZ-EVALZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable VCOM Calibrator with EEPROM |
| ISL24202IRTZ-T13 | 功能描述:LCD Gamma緩沖器 ISL24202IRTZFREE VCM CLBTR W/AN I2C RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| ISL24211 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable VCOM Calibrator with EEPROM and Output Buffer |
| ISL24211IRTZ | 功能描述:LCD Gamma緩沖器 ISL24211IRTZFREE VCO M DRVR + VCOM CLBTR RoHS:否 制造商:Maxim Integrated 輸入補償電壓: 轉換速度: 電源電壓-最大:20 V 電源電壓-最小:9 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-38 封裝:Tube |
| ISL24211IRTZ-EVALZ | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Programmable VCOM Calibrator with EEPROM and Output Buffer |
發布緊急采購，3分鐘左右您將得到回復。