- 您現在的位置：買賣IC網 > PDF目錄17646 > ISL23345WFRZ-TK (Intersil)IC DGTL POT 256POS 10K 20TSSOP PDF資料下載
參數資料
| 型號： | ISL23345WFRZ-TK |
| 廠商： | Intersil |
| 文件頁數： | 6/19頁 |
| 文件大小： | 0K |
| 描述： | IC DGTL POT 256POS 10K 20TSSOP |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 4 |
| 溫度系數： | 標準值 125 ppm/°C |
| 存儲器類型： | 易失 |
| 接口： | I²C，2 線串口 |
| 電源電壓： | 1.2 V ~ 5.5 V，1.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | * |
| 封裝/外殼： | * |
| 供應商設備封裝： | * |
| 包裝： | * |
ISL23345
14
FN7872.0
June 21, 2011
pins in order to initiate communication with the ISL23345. A
maximum of eight ISL23345 devices may occupy the I2C serial
bus (see Table 3).
VLOGIC
Digital power source for the logic control section. It supplies an
internal level translator for 1.2V to 5.5V serial bus operation. Use
the same supply as the I2C logic source.
Principles of Operation
The ISL23345 is an integrated circuit incorporating four DCPs
with its associated registers and an I2C serial interface providing
direct communication between a host and the potentiometer.
The resistor array is comprised of individual resistors connected
in series. At either end of the array and between each resistor is
an electronic switch that transfers the potential at that point to
the wiper.
The electronic switches on the device operate in a
“make-before-break” mode when the wiper changes tap
positions.
Voltage at any of the DCP pins, RHi, RLi or RWi, should not
exceed VCC level at any conditions during power-up and normal
operation.
The VLOGIC pin is the terminal for the logic control digital power
source. It should use the same supply as the I2C logic source,
which allows reliable communication with a wide range of
microcontrollers and is independent from the VCC level. This is
extremely important in systems where the master supply has
lower levels than the DCP analog supply.
DCP Description
Each DCP is implemented with a combination of resistor elements
and CMOS switches. The physical ends of each DCP are equivalent
to the fixed terminals of a mechanical potentiometer (RHi and RLi
pins). The RWi pin of the DCP is connected to intermediate nodes,
and is equivalent to the wiper terminal of a mechanical
potentiometer. The position of the wiper terminal within the DCP is
controlled by an 8-bit volatile Wiper Register (WRi). When the WRi of
a DCP contains all zeroes (WRi[7:0] = 00h), its wiper terminal (RW)
is closest to its “Low” terminal (RLi). When the WRi register of a DCP
contains all ones (WRi[7:0] = FFh), its wiper terminal (RWi) is closest
to its “High” terminal (RHi). As the value of the WRi increases from
all zeroes (0) to all ones (255 decimal), the wiper moves
monotonically from the position closest to RLi to the position closest
to RHi. At the same time, the resistance between RWi and RLi
increases monotonically, while the resistance between RHi and RWi
decreases monotonically.
While the ISL23345 is being powered up, all the wipers (WRi) are
reset to 80h (128 decimal), which positions RWi at the center
between RLi and RHi.
The WRi can be read or written to directly using the I2C serial
interface as described in the following sections.
Memory Description
The ISL23345 contains five volatile 8-bit registers: Wiper Register
WR0, Wiper Register WR1, Wiper Register WR2, Wiper Register
WR3 and Access Control Register (ACR). The memory map of
ISL23345 is shown in Table 1. The Wiper Register WRi at address i
contains current wiper position of DCPi (i = 0, 1, 2, 3). The Access
Control Register (ACR) at address 10h contains information and
control bits described in Table 2.
Shutdown Function
The SHDN bit (ACR[6]) disables or enables shutdown mode for all
DCP channels simultaneously. When this bit is 0, i.e. DCP is forced
to end-to-end open circuit and RW is connected to RL through a
SHDN bit is 1.
When the device enters shutdown, all current DCP WRi settings are
maintained. When the device exits shutdown, the wipers will return
to the previous WRi settings after a short settling time (see
Figure 26).
In shutdown mode, if there is a glitch on the power supply which
causes it to drop below 1.3V for more than 0.2s to 0.4s, the
wipers will be RESET to their mid positions. This is done to avoid
an undefined state at the wiper outputs.
TABLE 1. MEMORY MAP
ADDRESS
(hex)
VOLATILE
REGISTER NAME
DEFAULT SETTING
(hex)
10
ACR
40
3WR3
80
2WR2
80
1WR1
80
0WR0
80
TABLE 2. ACCESS CONTROL REGISTER (ACR)
BIT #
7
6
5
4
32
10
NAME/
VALUE
0SHDN
0
00
FIGURE 25. DCP CONNECTION IN SHUTDOWN MODE
2k
RW
RL
RH
相關PDF資料 |
PDF描述 |
|---|---|
| 30-17 BLK-EW | SWITCH PUSH SPST-NO 1A 115V |
| TM7EX101 | TRIMMER 100 OHM 0.5W TH |
| TM7ES504 | TRIMMER 500K OHM 0.5W TH |
| ISL23345UFVZ-TK | IC DGTL POT 256POS 50K 20QFN |
| ISL23345UFRZ-TK | IC DGTL POT 256POS 50K 20QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL23345WFVZ | 功能描述:數字電位計 IC 256 TAP VOLATILE I2C QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23345WFVZ-T7A | 功能描述:數字電位計 IC 256 TAPVOLATILE I2C QUAD FL RNG IND 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23345WFVZ-TK | 功能描述:數字電位計 IC 256 TAP VOLATILE I2C QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL23348 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad, 128 Tap, Low Voltage Digitally Controlled Potentiometer (XDCPa?￠) |
| ISL23348TFRZ | 功能描述:數字電位計 IC 128 TAP VOLATILE I2C QD FL RNG DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。