- 您現在的位置：買賣IC網 > PDF目錄9229 > ISL22444TFR20Z-TK (Intersil)IC POT DGTL 256TP LN LP 20-QFN PDF資料下載
參數資料
| 型號： | ISL22444TFR20Z-TK |
| 廠商： | Intersil |
| 文件頁數： | 6/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 256TP LN LP 20-QFN |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 100k |
| 電路數： | 4 |
| 溫度系數： | 標準值 ±45 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-VQFN 裸露焊盤 |
| 供應商設備封裝： | 20-QFN 裸露焊盤（5x5） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
14
FN6426.0
May 24, 2007
Applications Information
Communicating with ISL22444
Communication with ISL22444 proceeds using SPI interface
through the ACR (address 10000b), IVRi (address 00000b,
00001b, 00010b or 00011b), WRi (addresses 00000b,
00001b, 00010b or 00011b) and General Purpose registers
(addresses from 00100b to 01110b).
The wiper position of each potentiometer is controlled by the
corresponding WRi register. Writes and reads can be made
directly to these registers to control and monitor the wiper
position without any non-volatile memory changes. This is
done by setting MSB bit at address 10000b to 1 (ACR[7] = 1).
The non-volatile IVRi stores the power up position of the
wiper. IVRi is accessible when MSB bit at address 10000b is
set to 0 (ACR[7] = 0). Writing a new value to the IVRi register
will set a new power up position for the wiper. Also, writing to
this register will load the same value into the corresponding
WRi as the IVRi. Reading from the IVRi will not change the
WRi, if its contents are different.
Daisy Chain Configuration
When application needs more then one ISL22444, it can
communicate with all of them without additional CS lines by
daisy chaining the DCPs as shown on Figure 18. In Daisy
Chain configuration the SDO pin of previous chip is
connected to SDI pin of the following chip, and each CS and
SCK pins are connected to the corresponding
microcontroller pins in parallel, like regular SPI interface
implementation. The Daisy Chain configuration can also be
used for simultaneous setting of multiple DCPs. Note, the
number of daisy chained DCPs is limited only by the driving
capabilities of SCK and CS pins of microcontroller; for larger
number of SPI devices buffering of SCK and CS lines is
required.
Daisy Chain Write Operation
The write operation starts by HIGH to LOW transition on CS
line, followed by N two bytes write instructions on SDI line
with reversed chain access sequence: the instruction byte +
data byte for the last DCP in chain is going first, as shown on
Figure 19. The serial data is going through DCPs from DCP0
to DCP(N-1) as follows: DCP0 --> DCP1 --> DCP2 --> ... -->
DCP(N-1). The write instruction is executed on the rising
edge of CS for all N DCPs simultaneously.
Daisy Chain Read Operation
The read operation consists of two parts: first, send read
instructions (N two bytes operation) with valid address;
second, read the requested data while sending NOP
instructions (N two bytes operation) as shown on Figure 20
and Figure 21.
The first part starts by HIGH to LOW transition on CS line,
followed by N two bytes read instruction on SDI line with
reversed chain access sequence: the instruction byte +
dummy data byte for the last DCP in chain is going first,
followed by LOW to HIGH transition on CS line. The read
instructions are executed during second part of read
sequence. It also starts by HIGH to LOW transition on CS
line, followed by N two bytes NOP instructions on SDI line
and LOW to HIGH transition of CS. The data is read on
every even byte during second part of read sequence while
every odd byte contains instruction code + address from
which the data is being read.
Wiper Transition
When stepping up through each tap in voltage divider mode,
some tap transition points can result in noticeable voltage
transients, or overshoot/undershoot, resulting from the
sudden transition from a very low impedance “make” to a
much higher impedance “break within an extremely short
period of time (<50ns). Two such code transitions are EFh to
F0h, and 0Fh to 10h. Note, that all switching transients will
settle well within the settling time as stated on the datasheet.
A small capacitor can be added externally to reduce the
amplitude of these voltage transients, but that will also
reduce the useful bandwidth of the circuit, thus may not be a
good solution for some applications. It may be a good idea,
in that case, to use fast amplifiers in a signal chain for fast
recovery.
CS
SCK
SDI
SDO
RD
ADDR
NOP
RD
ADDR
READ DATA
1
8
16
24
32
FIGURE 17. FOUR BYTE READ SEQUENCE
ISL22444
相關PDF資料 |
PDF描述 |
|---|---|
| ISL22444UFR20Z-TK | IC POT DGTL 256TP LN LP 20-QFN |
| VE-21R-MY-F3 | CONVERTER MOD DC/DC 7.5V 50W |
| VE-21R-MY-F2 | CONVERTER MOD DC/DC 7.5V 50W |
| ISL22444TFV20Z-TK | IC POT DGTL 256TP LN LP 20-TSSOP |
| VE-21R-MY-F1 | CONVERTER MOD DC/DC 7.5V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22444TFV20Z | 功能描述:數字電位計 IC 267 TAP FL RNG IND QD SPI DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22444TFV20Z-TK | 功能描述:數字電位計 IC 270 TAP FL RNG IND QD SPI DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22444UFR20Z | 功能描述:數字電位計 IC 274 TAP FL RNG IND QD SPI DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22444UFR20Z-TK | 功能描述:數字電位計 IC 277 TAP FL RNG IND QD SPI DCP 5X5 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22444UFV20Z | 功能描述:數字電位計 IC 268 TAP FL RNG IND QD SPI DCP 20LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。