- 您現在的位置：買賣IC網 > PDF目錄9233 > ISL22424WFV14Z-TK (Intersil)IC POT DGTL 256TP LN LP 14-TSSOP PDF資料下載
參數資料
| 型號： | ISL22424WFV14Z-TK |
| 廠商： | Intersil |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 256TP LN LP 14-TSSOP |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 10k |
| 電路數： | 2 |
| 溫度系數： | 標準值 ±85 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | 4 線 SPI（芯片選擇） |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 14-TSSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
11
FN6425.0
May 31, 2007
Pin Description
Potentiometer Pins
RHI AND RLI
The high (RHi) and low (RLi) terminals of the ISL22424 are
equivalent to the fixed terminals of a mechanical potentiometer.
RHi and RLi are referenced to the relative position of the wiper
and not the voltage potential on the terminals. With WRi set to
255 decimal, the wiper will be closest to RHi, and with the WRi
set to 0, the wiper is closest to RLi.
RWI
RWi is the wiper terminal and is equivalent to the movable
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the WRi register.
Bus Interface Pins
SERIAL CLOCK (SCK)
This is the serial clock input of the SPI serial interface.
SERIAL DATA OUTPUT (SDO)
The SDO is a serial data output pin. During a read cycle, the
data bits are shifted out on the falling edge of the serial clock
SCK and will be available to the master on the following
rising edge of SCK.
The output type is configured through ACR[1] bit for Push -
Pull or Open Drain operation. Default setting for this pin is
Push - Pull. An external pull up resistor is required for Open
Drain output operation. Note: the external pull up voltage not
allowed beyond VCC.
SERIAL DATA INPUT (SDI)
The SDI is the serial data input pin for the SPI interface. It
receives device address, operation code, wiper address and
data from the SPI remote host device. The data bits are
shifted in at the rising edge of the serial clock SCK, while the
CS input is low.
CHIP SELECT (CS)
CS LOW enables the ISL22424, placing it in the active
power mode. A HIGH to LOW transition on CS is required
prior to the start of any operation after power up. When CS is
HIGH, the ISL22424 is deselected and the SDO pin is at
high impedance, and (unless an internal write cycle is
underway) the device will be in the standby state.
Principles of Operation
The ISL22424 is an integrated circuit incorporating two
DCPs with their associated registers, non-volatile memory
and the SPI serial interface providing direct communication
between host, potentiometers and memory. The resistor
arrays are comprised of individual resistors connected in a
series. At either end of the array and between each resistor
is an electronic switch that transfers the potential at that
point to the wiper.
The electronic switches on the device operate in a “make
before break” mode when the wiper changes tap positions.
When the device is powered down, the last value stored in
IVRi will be maintained in the non-volatile memory. When
power is restored, the content of the IVRi is recalled and
loaded into the corresponding WRi to set the wiper to the
initial position.
DCP Description
Each DCP is implemented with a combination of resistor
elements and CMOS switches. The physical ends of each
DCP are equivalent to the fixed terminals of a mechanical
potentiometer (RHi and RLi pins). The RWi pin of the DCP is
connected to intermediate nodes, and is equivalent to the
wiper terminal of a mechanical potentiometer. The position of
the wiper terminal within the DCP is controlled by an 8-bit
volatile Wiper Register (WRi). When the WRi of a DCP
FIGURE 13. MIDSCALE GLITCH, CODE 7Fh TO 80h
FIGURE 14. LARGE SIGNAL SETTLING TIME
Typical Performance Curves (Continued)
SCL
WIPER
CS
WIPER UNLOADED,
MOVEMENT FROM 0h to FFh
ISL22424
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B4F-MW-B1 | CONVERTER MOD DC/DC 72V 100W |
| VI-21T-MY-F4 | CONVERTER MOD DC/DC 6.5V 50W |
| VE-B4H-IU-B1 | CONVERTER MOD DC/DC 52V 200W |
| MS27505E17F6SD | CONN RCPT 6POS BOX MNT W/SCKT |
| VE-B4F-IU-B1 | CONVERTER MOD DC/DC 72V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22426 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Low Noise, Low Power, SPI Bus, 128 Taps |
| ISL22426UFR16Z | 功能描述:數字電位計 IC 128 TAP FL RNG IND DL DCP 16LD 4X4 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22426UFR16Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG IND DL DCP 20LD 4X4 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22426UFV14Z | 功能描述:數字電位計 IC 128 TAP FL RNG IND DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22426UFV14Z-TK | 功能描述:數字電位計 IC 128 TAP FL RNG IND DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。