- 您現在的位置：買賣IC網 > PDF目錄9245 > ISL22323TFR16Z-TK (Intersil)IC POT DGTL 256TP LN LP 16-QFN PDF資料下載
參數資料
| 型號： | ISL22323TFR16Z-TK |
| 廠商： | Intersil |
| 文件頁數： | 7/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT DGTL 256TP LN LP 16-QFN |
| 產品培訓模塊： | Solutions for Industrial Control Applications |
| 標準包裝： | 1,000 |
| 系列： | XDCP™ |
| 接片： | 256 |
| 電阻（歐姆）： | 100k |
| 電路數： | 2 |
| 溫度系數： | 標準值 ±45 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.25 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-QFN-EP（4x4） |
| 包裝： | 帶卷 (TR) |
15
FN6422.1
March 13, 2008
Write Operation
A Write operation requires a START condition, followed by a
valid Identification Byte, a valid Address Byte, a Data Byte,
and a STOP condition. After each of the three bytes, the
ISL22323 responds with an ACK. At this time, the device
enters its standby state (See Figure 18).
The non-volatile write cycle starts after STOP condition is
determined and it requires up to 20ms delay for the next
non-volatile write. Thus, non-volatile registers must be
written individually.
Read Operation
A Read operation consist of a three byte instruction followed
by one or more Data Bytes (See Figure 19). The master
initiates the operation issuing the following sequence: a
START, the Identification byte with the R/W bit set to “0”, an
Address Byte, a second START, and a second Identification
byte with the R/W bit set to “1”. After each of the three bytes,
the ISL22323 responds with an ACK. Then the ISL22323
transmits Data Bytes as long as the master responds with an
ACK during the SCL cycle following the eighth bit of each
byte. The Data Bytes are from the registers indicated by an
internal pointer. This pointers initial value is determined by
the Address Byte in the Read operation instruction, and
increments by one during transmission of each Data Byte.
After reaching the memory location 0Fh, the pointer “rolls
over” to 00h, and the device continues to output data for
each ACK received.The master terminates the read
operation issuing a NACK (ACK) and a STOP condition
following the last bit of the last Data Byte (See Figure 19).
Applications Information
Wiper Transition
When stepping up through each tap in voltage divider mode,
some tap transition points can result in noticeable voltage
transients (or overshoot/undershoot) resulting from the
sudden transition from a very low impedance “make” to a
much higher impedance “break within an extremely short
period of time (<50ns). Two such code transitions are EFh to
F0h, and 0Fh to 10h. Note that all switching transients will
settle well within the settling time as stated on the datasheet.
A small capacitor can be added externally to reduce the
amplitude of these voltage transients, but that will also
reduce the useful bandwidth of the circuit, thus this may not
be a good solution for some applications. It may be a good
idea, in that case, to use fast amplifiers in a signal chain for
fast recovery.
Application Example
Figure 20 shows an example of using ISL22323 for gain
setting and offset correction in high side current
measurement application. DCP0 applies a programmable
offset voltage of ±25mV to the FB+ pin of the Instrumentation
Amplifier EL8173 to adjust output offset to zero voltages.
DCP1 programs the gain of the EL8173 from 90 to 110 with
5V output for 10A current through current sense resistor.
ISL22323
相關PDF資料 |
PDF描述 |
|---|---|
| DS1013S-20+T&R | IC DELAY LINE 20NS 16-SOIC |
| VI-24R-MW | CONVERTER MOD DC/DC 7.5V 100W |
| ISL22323UFR16Z-TK | IC POT DGTL 256TP LN LP 16-QFN |
| VI-24P-MX-B1 | CONVERTER MOD DC/DC 13.8V 75W |
| DS1013S-20+ | IC DELAY LINE 20NS 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISL22323TFV14Z | 功能描述:數字電位計 IC 256 TAP FL RNG IND DL I2C DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22323TFV14Z-TK | 功能描述:數字電位計 IC 256 TAP FL RNG IND DL I2C DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22323UFR16Z | 功能描述:數字電位計 IC 256 TAP FL RNG IND DL I2C DCP 4X4 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22323UFR16Z-TK | 功能描述:數字電位計 IC 256 TAP FL RNG IND DL I2C DCP 4X4 RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| ISL22323UFV14Z | 功能描述:數字電位計 IC 256 TAP FL RNG IND DL I2C DCP 14LD RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。