參數資料
型號： IS82C55A-5Z
廠商： Intersil
文件頁數： 2/29頁
文件大?。?/td> 0K
描述： IC I/O EXPANDER 24B 44PLCC
標準包裝： 260
接口： 可編程
輸入/輸出數： 24
中斷輸出： 無
電源電壓： 4.5 V ~ 5.5 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 44-LCC（J 形引線）
供應商設備封裝： 44-PLCC
包裝： 管件
10
FN2969.10
November 16, 2006
INTR (Interrupt Request)
A “high” on this output can be used to interrupt the CPU
when an input device is requesting service. INTR is set by
the condition: STB is a “one”, IBF is a “one” and INTE is a
“one”. It is reset by the falling edge of RD. This procedure
allows an input device to request service from the CPU by
simply strobing its data into the port.
INTE A
Controlled by bit set/reset of PC4.
INTE B
Controlled by bit set/reset of PC2.
Output Control Signal Definition
(Figure 8 and 9)
OBF - (Output Buffer Full F/F). The OBF output will go “l(fā)ow”
to indicate that the CPU has written data out to the specified
port. This does not mean valid data is sent out of the port at
this time since OBF can go true before data is available.
Data is guaranteed valid at the rising edge of OBF, (See
Note 1). The OBF F/F will be set by the rising edge of the
WR input and reset by ACK input being low.
ACK - (Acknowledge Input). A “l(fā)ow” on this input informs the
82C55A that the data from Port A or Port B is ready to be
accepted. In essence, a response from the peripheral device
indicating that it is ready to accept data, (See Note 1).
INTR - (Interrupt Request). A “high” on this output can be
used to interrupt the CPU when an output device has
accepted data transmitted by the CPU. INTR is set when
ACK is a “one”, OBF is a “one” and INTE is a “one”. It is reset
by the falling edge of WR.
INTE A
Controlled by Bit Set/Reset of PC6.
INTE B
Controlled by Bit Set/Reset of PC2.
NOTE:
1. To strobe data into the peripheral device, the user must operate
the strobe line in a hand shaking mode. The user needs to send
OBF to the peripheral device, generates an ACK from the
peripheral device and then latch data into the peripheral device
on the rising edge of OBF.
FIGURE 7. MODE 1 (STROBED INPUT)
tST
STB
INTR
RD
INPUT FROM
IBF
PERIPHERAL
tSIB
tSIT
tPH
tPS
tRIT
tRIB
FIGURE 8. MODE 1 OUTPUT
1
D7
0
D6
1
D5
1
D4
1/0
D3 D2 D1 D0
CONTROL WORD
MODE 1 (PORT A)
PC7
8
ACKA
PC6
PA7-PA0
OBFA
INTRA
PC3
PC4, PC5
2
WR
PC4, PC5
1 = INPUT
0 = OUTPUT
1
D7 D6 D5 D4 D3 D2 D1 D0
CONTROL WORD
MODE 1 (PORT B)
PC1
8
ACKB
PC2
INTE
B
PB7-PB0
OBFB
INTRB
PC0
WR
10
INTE
A
82C55A
相關PDF資料
PDF描述
CS82C55A-596 IC I/O EXPANDER 24B 44PLCC
CS82C55A-5 IC I/O EXPANDER 24B 44PLCC
ATMEGA8535L-8AUR MCU AVR 8K FLASH 8MHZ 44TQFP
CP82C55A-5 IC I/O EXPANDER 24B 40DIP
ATMEGA8535-16MUR MCU AVR 8K FLASH 16MHZ 44QFN
相關代理商/技術參數
參數描述
IS82C55A-5Z96 功能描述:外圍驅動器與原件 - PCI W/ANNEAL PERIPH PRG- I/O 5V 5MHZ 44PLCC RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
IS82C55A96 功能描述:外圍驅動器與原件 - PCI PERIPH PRG-I/O 5V 8MHZ 44PLCC INDEL RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
IS82C55AR2490 制造商:Rochester Electronics LLC 功能描述:- Bulk
IS82C55AZ 功能描述:外圍驅動器與原件 - PCI PERI PRG-I/O 5V 8MHZ 44PLCC IND RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
IS82C55AZ 制造商:Intersil Corporation 功能描述:IC TRANSCEIVER 8V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*