- 您現在的位置：買賣IC網 > PDF目錄11818 > IS82C50A-5 (Intersil)IC PERIPH UART/BRG 10MHZ 44-PLCC PDF資料下載
參數資料
| 型號： | IS82C50A-5 |
| 廠商： | Intersil |
| 文件頁數： | 2/25頁 |
| 文件大小： | 0K |
| 描述： | IC PERIPH UART/BRG 10MHZ 44-PLCC |
| 標準包裝： | 26 |
| 特點： | 單芯片 UART/BRG |
| 通道數： | 1，UART |
| 規程： | RS232C |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 帶并行端口： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC |
| 包裝： | 管件 |
10
FN2958.5
August 24, 2006
82C50A
MCR(3): When MCR(3) is set high, the OUT2 output is
forced low. When MCR(3) is reset low, the OUT2 output is
forced high. OUT2 is an user designated output.
MCR(4): MCR(4) provides a local loopback feature for
diagnostic testing of the 62C50A. When MCR(4) is set high,
Serial Output (SOUT) is set to the marking (logic 1) state,
and the receiver data input Serial Input (SIN) is
disconnected. The output of the Transmitter Shift Register is
looped back into the Receiver Shift Register input. The four
modem control inputs (CTS, DSR, DC, and RI) are
disconnected. The four modem control outputs (DTR, RTS,
OUT1 and OUT2) are internally connected to the four
modem control inputs. The modem control output pins are
forced to their inactive state (high). In the diagnostic mode,
data transmitted is immediately received. This allows the
processor to verify the transmit and receive data paths of the
82C50A.
In the diagnostic mode, the receiver and transmitter
interrupts are fully operational. The modem control interrupts
are also operational, but the interrupt sources are now the
lower four bits of the MCR instead of the four modem control
inputs. The interrupts are still controlled by the Interrupt
Enable Register.
MCR(5) - MCR(7): These bits are permanently set to logic 0.
MODEM STATUS REGISTER (MSR)
The MSR provides the CPU with status of the modem input
lines from the modem or peripheral device. The MSR allows
the CPU to read the modem signal inputs by accessing the
data bus interface of the 82C50A. In addition to the current
status information, four bits of the MSR indicate whether the
modem inputs have changed since the last reading of the
MSR. The delta status bits are set high when a control input
from the modem changes state, and reset low when the
CPU reads the MSR.
The modem input lines are CTS (pin 36), DSR (pin 37), RI
(pin 39), and DCD (pin 38). MSR(4) - MSR(7) are status
indications of these lines. The status indications follow the
status of the input lines. If the modem status interrupt in the
Interrupt Enable Register is enabled (IER(3)), a change of
state in a modem input signals will be reflected by the
modem status bits in the lIR register, and an interrupt
(lNTRPT) is generated. The MSR is a priority 4 interrupt. The
contents of the Modem Status Register are described below:
Note that the state (high or low) of the status bits are
inverted versions of the actual input pins.
MSR(0) Delta Clear to Send (DCTS): DCTS indicates that
the CTS input (Pin-36) to the 82C50A has changed state
since the last time it was read by the CPU.
MSR(1) Delta Data Set Ready (DDSR): DDSR indicates
that the DSR input (Pin-37) to the 62C50A has changed
state since the last time it was read by the CPU.
MSR(2) Trailing Edge of Ring Indicator (TERI): TERI
indicates that the RI input (Pin-39) to the 82C50A has
Changed state from Low to High since the last time it was
read by the CPU. High to Low transitions on RI do not
activate TERI.
MODEM CONTROL REGISTER (MCR)
MCR
7
MCR
6
MCR
5
MCR
4
MCR
3
MCR
2
MCR
1
MCR
0
Data Terminal
Ready
0 = DTR Output High (Inactive)
1 = DTR Output Low (Active)
Request to
Send
0 = RTS Output High (Inactive)
1 = RTS Output Low (Active)
Out 1
0 = OUT 1 Output High (Inactive)
1 = OUT 1 Output Low (Active)
Out 2
0 = OUT 2 Output High (Inactive)
1 = OUT 2 Output Low (Active)
Loop
0 = Loop Disabled
1 = Loop Enabled
These Bits are Permanently Set to a Logic 0.
MSR BITS 0 THRU 7
MSR BIT
MNEMONIC
DESCRIPTION
MSR (1)
DDSR
Delta Data Set Ready
MSR (2)
TERI
Trailing Edge of Ring Indicator
MSR (0)
DCTS
Delta Clear To Send
MSR (3)
DDCD
Delta Data Carrier Detect
MSR (4)
CTS
Clear To Send
MSR (5)
DSR
Data Set Ready
MSR (6)
RI
Ring Indicator
MSR (7)
DCD
Data Carrier Detect
相關PDF資料 |
PDF描述 |
|---|---|
| IS82C50A-5Z | IC PERIPH UART/BRG 10MHZ 44-PLCC |
| ATMEGA329-16MUR | MCU AVR 32K FLASH 16MHZ 64QFN |
| CS82C50A-5Z96 | IC ASYNC COMM ELEMNT UART 44PLCC |
| CS82C50A-5Z | IC COMMUNICATION ELEMENT 44-PLCC |
| CP82C52Z | IC UART/BRG 5V 16MHZ 28-PDIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IS82C50A-5Z | 功能描述:UART 接口集成電路 W/ANNEAL PERIPH UART /BRG 5V 10MHZ RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| IS82C52 | 功能描述:UART 接口集成電路 PERIPH UART/BRG 5V 16MHZ 28PLCC IND RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| IS82C52/TR100/BAE | 制造商:Intersil Corporation 功能描述:PERIPH UART/BRG 5V 16MHZ 28PLCC IND - Tape and Reel |
| IS82C5296 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| IS82C52R2490 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。