- 您現在的位置：買賣IC網 > PDF目錄377541 > IRU3037CS (International Rectifier) RES CHIP 383OHM 1/10 1% 100PP PDF資料下載
參數資料
| 型號： | IRU3037CS |
| 廠商： | International Rectifier |
| 英文描述： | RES CHIP 383OHM 1/10 1% 100PP |
| 中文描述： | 8引腳同步PWM控制器 |
| 文件頁數： | 6/21頁 |
| 文件大?。?/td> | 220K |
| 代理商： | IRU3037CS |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁
6
Rev. 2.8
05/10/04
IRU3037 / IRU3037A
www.irf.com
Assuming the following:
V = 1%(V
IN
), Efficiency(
η
) = 90%
By using equation (3), C
IN
= 193.3
μ
F
For higher efficiency, low ESR capacitor is recommended.
Choose two 100
μ
F capacitors.
The Sanyo TPB series PosCap capacitor 100
μ
F, 10V
with 55m
ESR is a good choice.
Output Capacitor Selection
The criteria to select the output capacitor is normally
based on the value of the Effective Series Resistance
(ESR). In general, the output capacitor must have low
enough ESR to meet output ripple and load transient
requirements, yet have high enough ESR to satisfy sta-
bility requirements. The ESR of the output capacitor is
calculated by the following relationship:
V
I
O
The Sanyo TPC series, PosCap capacitor is a good
choice. The 6TPC150M 150
μ
F, 6.3V has an ESR 40m
.
Selecting two of these capacitors in parallel, results to
an ESR of
20m
which achieves our low ESR goal.
The capacitor value must be high enough to absorb the
inductor's ripple current. The larger the value of capaci-
tor, the lower will be the output ripple voltage.
Inductor Selection
The inductor is selected based on output power, operat-
ing frequency and efficiency requirements. Low inductor
value causes large ripple current, resulting in the smaller
size, but poor efficiency and high output noise. Gener-
ally, the selection of inductor value can be reduced to
desired maximum ripple current in the inductor (
i). The
optimum point is usually found between 20% and 50%
ripple of the output current.
For the buck converter, the inductor value for desired
operating ripple current can be determined using the fol-
lowing relation:
If
i = 20%(I
O
), then the output inductor will be:
L = 7
μ
H
The Toko D124C series provides a range of inductors in
different values, low profile suitable for large currents,
10
μ
H, 4.2A is a good choice for this application. This
will result to a ripple approximately 14% of output cur-
rent.
Power MOSFET Selection
The IRU3037 uses two N-Channel MOSFETs. The se-
lections criteria to meet power transfer requirements is
based on maximum drain-source voltage (V
DSS
), gate-
source drive voltage (V
GS
), maximum output current, On-
resistance R
DS(ON)
and thermal management.
The MOSFET must have a maximum operating voltage
(V
DSS
) exceeding the maximum input voltage (V
IN
).
The gate drive requirement is almost the same for both
MOSFETs. Logic-level transistor can be used and cau-
tion should be taken with devices at very low V
GS
to pre-
vent undesired turn-on of the complementary MOSFET,
which results a shoot-through current.
The total power dissipation for MOSFETs includes con-
duction and switching losses. For the Buck converter
the average inductor current is equal to the DC load cur-
rent. The conduction loss is defined as:
The R
DS(ON)
temperature dependency should be consid-
ered for the worst case operation. This is typically given
in the MOSFET data sheet. Ensure that the conduction
losses and switching losses do not exceed the package
ratings or violate the overall thermal budget.
2
P
COND
(Upper Switch) = I
LOAD
×
R
DS(ON)
×
D
×
P
COND
(Lower Switch) = I
2
×
R
DS(ON)
×
(1 - D)
×
= R
DS(ON)
Temperature Dependency
Where:
V
O
= Output Voltage Ripple
I
O
= Output Current
V
O
=100mV and
I
O
=4A
Results to ESR=25m
ESR
≤
---(4)
Where:
V
IN
= Maximum Input Voltage
V
OUT
= Output Voltage
i = Inductor Ripple Current
f
S
= Switching Frequency
t = Turn On Time
D = Duty Cycle
V
IN
- V
OUT
= L
×
i
t = D
×
; D =
t
1
f
S
V
OUT
V
IN
L = (V
IN
- V
OUT
)
×
V
V
IN
×
i
×
f
S
OUT
t = D
×
t = 3.3
μ
s
f
S
V
×
I
IN
1
I
IN
= V
I
IN
= 2.93A
相關PDF資料 |
PDF描述 |
|---|---|
| IRU3055CQ | POWER MANAGEMENT CHIPSET FOR 3-PHASE VRM 9.0 CONVERTERS |
| IRUK3055CQ01 | POWER MANAGEMENT CHIPSET FOR 3-PHASE VRM 9.0 CONVERTERS |
| IRUK3055CQ01TR | POWER MANAGEMENT CHIPSET FOR 3-PHASE VRM 9.0 CONVERTERS |
| IRU3055 | 5-BIT PROGRAMMABLE 3-PHASE SYNCHRONOUS BUCK CONTROLLER IC |
| IRU3073 | SYNCHRONOUS PWM CONTROLLER WITH OVER-CURRENT PROTECTION / LDO CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRU3037CSPBF | 功能描述:IC REG CTRLR BUCK PWM VM 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| IRU3037CSTR | 功能描述:電壓模式 PWM 控制器 8 PWM 200 KHZ 200kHz Synch CTRL RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓?fù)浣Y(jié)構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| IRU3037CSTRPBF | 功能描述:開關變換器、穩壓器與控制器 8 PWM 200 KHZ 200kHz Synch CTRL RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| IRU3038 | 制造商:IRF 制造商全稱:International Rectifier 功能描述:SYNCHRONOUS PWM CONTROLLER FOR TERMINATION POWER SUPPLY APPLICATIONS |
| IRU3038CF | 功能描述:IC REG CTRLR BUCK PWM VM TSSOP14 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,000 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:50% 電源電壓:9 V ~ 10 V 降壓:無 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。