- 您現在的位置：買賣IC網 > PDF目錄360972 > IRU1261CM Dual 1A and 6A Fixed LDO Linear Regulator in a TO-263 5-Leads package PDF資料下載
參數資料
| 型號： | IRU1261CM |
| 英文描述： | Dual 1A and 6A Fixed LDO Linear Regulator in a TO-263 5-Leads package |
| 中文描述： | 雙1A和采用TO - 263 5 6A條固定LDO線性穩壓器，信息包 |
| 文件頁數： | 4/8頁 |
| 文件大小： | 55K |
| 代理商： | IRU1261CM |
IRU1261
4
Rev. 2.0
09/19/02
www.irf.com
APPLICATION INFORMATION
Introduction
The IRU1261 is a dual fixed output Low Dropout (LDO)
regulator available in a TO-263 package. This voltage
regulator is designed specifically for Pentium
II
proces-
sor applications requiring 2.5V and 1.5V supplies, elimi-
nating the need for a second regulator resulting in lower
overall system cost. The IRU1261 is designed to take
advantage of 5V supply to provide the drive for the pass
transistor, allowing 2.5V supply to be generated from
3.3V input. This feature improves the power dissipation
of the 2.5V regulator substantially allowing a smaller
heat sink to be used for the application. Compared to
the IRU1260 dual adjustable regulator, the IRU1261 in-
cludes the resistor dividers that are otherwise needed
with the IRU1260, eliminating four external components
and their tolerances, resulting in a more accurate initial
accuracy for each output voltage. Other features of the
device include: fast response to sudden load current
changes, such as GTL+ termination application and ther-
mal shutdown protection to protect the device if an over-
load condition occurs.
Stability
The IRU1261 requires the use of an output capacitor as
part of the frequency compensation in order to make the
regulator stable. Typical designs for the microprocessor
applications use standard electrolytic capacitors with
typical ESR in the range of 50 to 100m
and the output
capacitance of 500 to 1000
μ
F. Fortunately as the ca-
pacitance increases, the ESR decreases resulting in a
fixed RC time constant. The IRU1261 takes advantage
of this phenomena in making the overall regulator loop
stable. For most applications a minimum of 100
μ
F alu-
minum electrolytic capacitor with the maximum ESR of
0.3
such as Sanyo, MVGX series, Panasonic FA se-
ries as well as the Nichicon PL series insures both sta-
bility and good transient response. The IRU1261 also
requires a 1
μ
F ceramic capacitor connected from V
IN
to
V
CTRL
and a 10
, 0.1W resistor in series with V
CTRL
pin
in order to further insure stability.
Thermal Design
The IRU1261 incorporates an internal thermal shutdown
that protects the device when the junction temperature
exceeds the maximum allowable junction temperature.
Although this device can operate with junction tempera-
tures in the range of 150
8
C, it is recommended that the
selected heat sink be chosen such that during maxi-
mum continuous load operation the junction tempera-
ture is kept below this number. The example given shows
the steps in selecting the proper regulator heat sink for
driving the Pentium
II
processor GTL+ termination re-
sistors and the Clock IC using IRU1261 in TO-263 pack-
age.
Example
:
Assuming the following specifications:
The steps for selecting a proper heat sink to keep the
junction temperature below 135
8
C is given as:
1) Calculate the maximum power dissipation using:
2) Assuming a TO-263 surface mount package, the junc-
tion to ambient thermal resistance of the package is:
3) The maximum junction temperature of the device is
calculated using the equation below:
Since this is lower than our selected 135
8
C maxi-
mum junction temperature (150
8
C is the thermal shut-
down of the device), TO-263 package is a suitable
package for our application.
Layout Consideration
The IRU1261 like all other high speed linear regulators
need to be properly laid out to insure stable operation.
The most important component is the output capacitor,
which needs to be placed close to the output pin and
connected to this pin using a plane connection with a
low inductance path.
V
IN
= 3.3V
V
OUT1
= 2.5V
V
OUT2
= 1.5V
I
OUT1(MAX)
= 0.2A
I
OUT2(MAX)
= 1.5A
T
A
= 35
8
C
P
D
= I
OUT1
×
(V
IN
- V
OUT1
) + I
OUT2
×
(V
IN
- V
OUT2
)
P
D
= 0.2
×
(3.3 - 2.5) + 1.5
×
(3.3 - 1.5) = 2.86W
θ
JA
= 30
8
C/W for 1" square pad area
T
J
= T
A
+ P
D
×θ
JA
T
J
= 35 + 2.86
×
30 = 121
8
C
相關PDF資料 |
PDF描述 |
|---|---|
| IRU1261CP | VOLT REGULATOR|FIXED|+1.5V & +2.5V|BIPOLAR|SIP|3PIN|PLASTIC |
| IRU1261CT | VOLT REGULATOR|FIXED|+1.5V & +2.5V|BIPOLAR|ZIP|5PIN|PLASTIC |
| IRU3005CW | |
| IRU3034CS | 8 Pin PWM Switcher CIC with Current Limiting in a 8-Pin SOIC(NB) package |
| IRU431ALCS | VOLT REGULATOR|ADJUSTABLE|+1.24 TO +15V|BIPOLAR|SOP|8PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRU1261CMTR | 功能描述:IC CONV PENTIUM II TO-263-5 RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| IRU1261CP | 制造商:IRF 制造商全稱:International Rectifier 功能描述:DUAL 6A AND 1A LOW DROPOUT POSITIVE FIXED 1.5V AND 2.5V REGULATOR |
| IRU1261CPTR | 功能描述:IC CONV PENTIUM II 7-UTHINP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
| IRU1261CT | 制造商:International Rectifier 功能描述:IC, DUAL LDO VOLT REG, 1.5V/2.5V TO220-5, Primary Input Voltage:3.6V, Output Vol |
| IRU1502-33 | 制造商:IRF 制造商全稱:International Rectifier 功能描述:MICROPOWER 1A LOW DROPOUT PMOS VOLTAGE REGULATOR |
發布緊急采購，3分鐘左右您將得到回復。