- 您現在的位置：買賣IC網 > PDF目錄377537 > IRPT1065A (International Rectifier) Power Module for 0.75kW Motor Drives(0.75kW 馬達驅動器的功率模塊) PDF資料下載
參數資料
| 型號： | IRPT1065A |
| 廠商： | International Rectifier |
| 英文描述： | Power Module for 0.75kW Motor Drives(0.75kW 馬達驅動器的功率模塊) |
| 中文描述： | 電源模塊功率0.75kW電動機驅動器（功率0.75kW馬達驅動器的功率模塊） |
| 文件頁數： | 6/12頁 |
| 文件大?。?/td> | 206K |
| 代理商： | IRPT1065A |
page 6
IRPT1065A
Mounting Procedure
Mounting
1. Connect the driver board and the IRPT1065A power
module.
2. Remove all particles and grit from the heat sink and power
substrate.
3. Spread a .004" to .005" layer of silicone grease on the heat
sink, covering the entire area that the power substrate will
occupy. Recommended heat sink flatners is .001 inch/inch and
Total Indicator Readout (TIR) of .003 inch below substrate.
4. Place the power substrate onto the heat sink with the
mounting holes aligned and press it firmly into the silicone
grease.
5. Place the 2 M4 mounting screws through the PCB and
power module and into the heat sink and tighten the screws to
1 Nm torque.
Pow er Connections
The power module pin designation, function and other details
can be obtained from the package outline in Figure 7 and circuit
diagram in Figure 8. Single phase input connections made to
pins S and T and inverter output connections are made to pins U,
V and W. Positive rectifier output and positive inverter bus are
brought out to pins RP and P respectively in order to provide DC
bus capacitor soft charging implementation option. The current
shunt terminals are connected to pins IS1, IS2 and IS3, IS4 on
the positive and negative DC rails respectively.
Heat Sink Requirements
Figures 3a-3b show the thermal resistance of the heat sink
required for various output power levels and Pulse-Width-
Modulated (PWM) switching frequencies. Maximum total losses
of the unit are also shown. This data is based on the following
key operating conditions:
The maximum continuous combined losses of the rectifier
and inverter occur at full pulse-width-modulation. These
maximum losses set the maximum continuous operating
temperature of the heat sink.
The maximum combined losses of the rectifier and inverter
at full pulse-width-modulation under overload set the
incremental temperature rise of the heat sink during
overload.
The minimum output frequency at which full load current
is to be delivered sets the peak IGBT junction temperature.
At low output frequency, IGBT junction temperature tends
to follow the instantaneous fluctuations of the output
current. Thus, peak junction temperature rise increases as
output frequency decreases.
Over Temperature Protection
Over temperature can be detected using the NTC thermistor
included in the power module for thermal sensing. Protection
circuit that initiates a shutdown if the temperature of the IMS
substrate exceeds a set level can be implemented. The nominal
resistance vs. temperature characteristic of the thermistor is
given in Figure 5.
Voltage Rise During Braking
The motor will feed energy back to the DC link during
regenerative braking, forcing the DC bus voltage to rise above
the level defined by the input line voltage. Deceleration of the
motor must be controlled by appropriate PWM control to keep
the DC bus voltage within the rated maximum value.
Functional Information
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
123456789012345678901234567890
Figure 6.
Power Module Mounting Screw Sequence
相關PDF資料 |
PDF描述 |
|---|---|
| IRPT2051A | Power Module for 2.2 kW Motor Drives(2.2kW 馬達驅動器的功率模塊) |
| IRPT2055A | Power Module for 1.5 kW Motor Drives(1.5kW 馬達驅動器的功率模塊) |
| IRPT2055 | Integrated Power Stage for 1.5kW Motor Drives(1.5kW 馬達驅動器的集成功率單元) |
| IRPT2056 | Power Module for 3 hp Motor Drives |
| IRPT2056A | Power Module for 2.2kW Motor Drives(2.2kW 馬達驅動器的功率模塊) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRPT1066A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| IRPT2051 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| IRPT2051A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| IRPT2055 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| IRPT2055A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。