- 您現在的位置：買賣IC網 > PDF目錄377537 > IRPLDIM1U (International Rectifier) Dimming Ballast Control IC Design Kit PDF資料下載
參數資料
| 型號： | IRPLDIM1U |
| 廠商： | International Rectifier |
| 英文描述： | Dimming Ballast Control IC Design Kit |
| 中文描述： | 調光鎮流器控制IC設計工具包 |
| 文件頁數： | 11/12頁 |
| 文件大小： | 209K |
| 代理商： | IRPLDIM1U |
11
www.irf.com
Figure 6, Normal Run mode, Upper trace: voltage
across RCS, Middle trace: IC2 LO pin voltage,
Lower trace: IC2 HO-VS pin voltage
Figure 7, Normal lamp ignition: Lamp voltage during the
end of Preheat mode, Ignition Ramp mode and the
beginning of the Run mode
During the Preheat mode the over-current protection is disabled. However, at the end of Preheat
mode (the beginning of the Ignition mode) the hard-switching and over-current detection are en-
abled. If at any time thereafter the voltage magnitude across resistor RCS rises above the over-
current threshold (1.6V) of the CS pin of IC2, a lamp fault condition is signaled and the half-bridge
output MOSFETs’, (M2 and M3) are turned off and the ballast goes into Fault mode. This can happen
if the lamp fails to ignite or if the upper filament is open. For failure to ignite the lamp, the current in
the half-bridge increases and thus the voltage across resistor RCS increases above the over-current
threshold signaling a fault. Figure 8 shows the voltage across resistor RCS and the voltage appear-
ing across the lamp when the ballast detects a failure to ignite the lamp and goes into Fault mode.
Figure 9 shows the voltage appearing across the lamp during the tail end of the Preheat mode and
the Ignition mode for a failure of the lamp to ignite condition. If the upper filament is open, the half-
bridge output hard-switches and each time the low side MOSFET (M3) is turned on a large current
pulse occurs and thus a large voltage pulse occurs across resistor RCS signaling a fault, Figure 10
shows this hard-switching condition. Figure 11 shows the lamp voltage during the Preheat mode and
beginning of Ignition Ramp mode for this hard-switching condition when the lamp fault condition is
detected. The ballast will remain in Fault mode until either the line voltage is cycled or a lamp re-
placement is performed.
相關PDF資料 |
PDF描述 |
|---|---|
| IRPLDIM2U | Digital Dimming DALI Ballast for 32W/T8 110V input |
| IRPT1053C | Power Module for 1 hp Motor Drives |
| IRPT1053A | Power Module for 0.75kW Motor Drives(0.75kW 馬達驅動器的功率模塊) |
| IRPT1053D | Power Module for 1 hp Motor Drives |
| IRPT1053E | Power Module for 1 hp Motor Drives |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRPLDIM2A | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Digitally Addressable DALI Dimming Ballast Reference Design |
| IRPLDIM2E | 功能描述:KIT BALLAST DIM DIG 230VAC RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 類型:MCU 適用于相關產品:Freescale MC68HC908LJ/LK（80-QFP ZIF 插口） 所含物品:面板、纜線、軟件、數據表和用戶手冊 其它名稱:520-1035 |
| IRPLDIM2U | 功能描述:BALLAST DIM DIG 32W/T8 120VAC RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| IRPLDIM3 | 功能描述:電源管理IC開發工具 3 lvl Dim CFL Fluor Ballast w/IRS2158D RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| IRPLDIM4E | 功能描述:電源管理IC開發工具 Miniature Dimmable 26W Ballast dsgn kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。