參數資料
型號： IRAUDAMP5
廠商： International Rectifier
英文描述： 120W x 2 Channel Class D Audio Power Amplifier Using the IRS2092S and IRF6645
中文描述： 120瓦× 2通道D類音頻功率放大器使用IRS2092S和IRF6645
文件頁數： 6/49頁
文件大?。?/td> 1416K
代理商： IRAUDAMP5
Test Procedures
1. Connect 4
, 250W load to both output connectors, J3 and J4 and Audio Precision
analyzer (AP).
2. Connect Audio Signal Generator to J6 and J5 for CH1 and CH2 respectively (AP).
3. Connect a dual power supply to J7, pre-adjusted to ±35V, as shown in Figure 2 above.
4. Set switch S3 to middle position (self oscillating).
5. Set volume level knob R108 fully counter-clockwise (minimum volume).
6. Turn on the power supply. Note: always apply or remove the ±35V at the same time.
7. Orange LED (Protection) should turn on almost immediately and turn off after about 3s.
8. Green LED (Normal) then turns on after orange LED is extinguished and should stay on.
9. One second after the green LED turns on; the two blue LEDS on the Daughter Board
should turn on and stay on for each channel, indicating that a PWM signal is present at
LO
10. With an Oscilloscope, monitor switching waveform at test points TP1 and TP2 of CH1
and CH2 on Daughter Board.
11. If necessary, adjust the self-oscillating switching frequency of AUDAMP5 to 400KHz
±
5kHz using potentiometer R29P. For IRAUDAMP5, the self-oscillating switching
frequency is pre-calibrated to 400KHz. To modify the AUDAMP5 frequency, change the
values of potentiometers R21 and R22 for CH1 and CH2 respectively.
12. Quiescent current for the positive supply should be 70mA
±
10mA at +35V.
13. Quiescent current for the negative supply should be 100mA
±
10mA at –35V.
14. Push S1 switch, (Trip and Reset push-button) to restart the sequence of LEDs indicators,
which should be the same as noted above in steps 6-9.
Audio Tests:
15. Apply 1 V RMS at 1KHz from the Audio Signal Generator
16. Turn control volume up (R108 clock-wise) to obtain an output reading of 100Watts for
all subsequent tests as shown on the Audio Precision graphs below, where measurements
are across J3 and J2 with an AES-17 Filter
Typical Performance
The tests below were performed under the following conditions:
±B supply = ±35V, load impedance = 4
resistive load, 1kHz audio signal,
Self oscillator @ 400kHz and internal volume-control set to give required output with 1Vrms
input signal, with AES-17 Filter, unless otherwise noted.
www.irf.com
Page 5 of 49
相關PDF資料
PDF描述
IRC4BC40F INSULATED GATE BIPOLAR TRANSISTOR
IRC530PBF HEXFET㈢ Power MOSFET
IRC540PBF HEXFET POWER MOSFET ( VDSS=100V , RDS(on)=0.077ヘ , ID=28A )
IRD3900 20 AND 30 AMP FAST RECOVERY RECTIFIER DIODES
IRD3910 DIODE SWITCHING DUAL COMMON-ANODE 240V 225mA-Io 350mW 50ns-trr SOT-23 3K/REEL
相關代理商/技術參數
參數描述
IRAUDAMP6 制造商:International Rectifier 功能描述:AUDIO REFERENCE DESIGN KIT FEATURING IRS20957 - Boxed Product (Development Kits) 制造商:International Rectifier 功能描述:BOARD EVAL FOR IRS20957S
IRAUDAMP7D 功能描述:放大器 IC 開發工具 25W - 500W Scalable IRS2092 2-Ch BRD RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
IRAUDAMP7S 功能描述:放大器 IC 開發工具 25W - 500W Scalable IRS2092 Half BRG BRD RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
IRAUDAMP8 功能描述:放大器 IC 開發工具 120W x 4 Ch Class D IRS2053M IRF665 BRD RoHS:否 制造商:International Rectifier 產品:Demonstration Boards 類型:Power Amplifiers 工具用于評估:IR4302 工作電源電壓:13 V to 23 V
IRAUDAMP9 功能描述:音頻 IC 開發工具 1.7kW 2ohm Class-D IRS2092 IRFB4227 BRD RoHS:否 制造商:Texas Instruments 產品:Evaluation Kits 類型:Audio Amplifiers 工具用于評估:TAS5614L 工作電源電壓:12 V to 38 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*