- 您現在的位置：買賣IC網 > PDF目錄377501 > IRADK10 (International Rectifier) 3-phase 115-230V 0.5HP Variable speed Motor Drive control for Appliances and light Industrial Applications. PDF資料下載
參數資料
| 型號： | IRADK10 |
| 廠商： | International Rectifier |
| 英文描述： | 3-phase 115-230V 0.5HP Variable speed Motor Drive control for Appliances and light Industrial Applications. |
| 中文描述： | 3相115 - 230伏0.5HP可變速電機驅動控制設備和輕型工業應用。 |
| 文件頁數： | 5/11頁 |
| 文件大?。?/td> | 881K |
| 代理商： | IRADK10 |
5
www.irf.com
IRADK10
PWM phase command signals
This carries the signals as shown below. Note that these
signals are referenced to the negative DC power rail which
is
not
at ground potential.
Beware of electric shock haz-
ard and
do not connect any grounded test equipment
such as an oscilloscope to these test pins.
Pin 1
: Phase A upper switch ON command, inverted
Pin 2
: Phase B upper switch ON command, inverted
Pin 3
: Phase C upper switch ON command, inverted
Pin 4
: Phase A lower switch ON command, inverted
Pin 5
: Phase B lower switch ON command, inverted
Pin 6
: Phase C lower switch ON command, inverted
Pin 7
: ITRIP signal
Pin 8
: SP1 spare digital input
Pin 9
: SP2 spare digital input
Pin 10
: GROUND (0V) referred to - DC bus
Pin 11
: Spare analog input referred to -DC bus rail
Pin 12
: +5V auxiliary power supply referred to - DC bus
rail
High voltage signals J2
This connector J2 carries the motor drive voltages and the
DC bus voltage. Use the same cautions as referenced
above for the PWM phase command signals.
Pin 1
: Phase A motor voltage
Pin 3
: Phase B motor voltage
Pin 5
: Phase C motor voltage
Pin 7
: MINUS DC bus rail
Pin 10
: PLUS DC bus rail
Power Connector J1
Power connector provides the input AC power and the
motor connections.
Pin 1
: Input AC voltage (115V or 220V) phase
Pin 2
: Input AC voltage (115V or 220V) neutral
Pin 3
: Ground connection ( has to be connected to
reduce the EMI noise)
Pin 4
: Ground connection
Pin 5
: Phase C motor connection
Pin 6
: Phase B motor connection
Pin 7
: Phase A motor connection
110V/220V selector switch S3
S3 is the selector switch to set the correct rectifier configu-
ration to the AC input.. Prior to connecting the system to the
AC input, carefully check the position of S3.
Operate the
switch only when the AC is OFF
. The drive will be dam-
aged and the user could be injured by ignoring this warning.
Connecting the inverter to the motor.
Use a 3-phase 115V Y connected or 220V delta connected
induction
motor
rated
Provide a 3 wire, 2A minimum rated cable for the motor con-
nection, and a 3 wire 2A minimum rated cable for the AC
mains connections. Make sure you also attach the ground
connection. The motor phase connections can be connected
in any sequence, only the rotation direction will be affected.
Make all the necessary connections, including the serial link
with the PC before applying AC power.
at
HP
or
less.
Operating the motor via the GUI tool.
After connecting all the cables and selecting the desired
settings in the GUI, apply the AC power via S2 in position 1.
After a few seconds, provided the main voltage is within tol-
erances, the yellow LED diode will flash denoting the pres-
ence of the DC-bus voltage.
Start the GUI tool. The first screen will prompt you for the
COM port used for PC to DEMO board communication as
is showed in the figure 4. Select either COM1 or COM2 for
this purpose.
Figure 4. GUI serial connection selections
This will lead you to the next screen. Observe at the top-left
a white field with the “DRIVE STATUS” label. Pressing the
“REFRESH SCREEN” button will read the drive status (ON,
OFF, eventual SC, OV, UV, I2T, and heat sink over tempera-
ture) and print a message in the top-left white field. Below
the “DRIVE STATUS” field, another white field is observed
with the caption “DC-link current average value over 5 sec-
onds”. Pressing the “REFRESH SCREEN” button will read
the drive DC-link current averaged over 5 seconds and dis-
play the value in mA units. Further below, in the same far left
column, another white field is observed with the caption “Heat
sink temperature”. Pressing the “REFRESH SCREEN” but-
ton will read the drive heat sink temperature and display the
value in degrees Centigrade.
相關PDF資料 |
PDF描述 |
|---|---|
| IRADK31 | 1/3 HP-Phase Brushless DC(BLDC) Motor Controller Using IR3101/3/4 |
| IRAM136-0461G | iMOTION⑩ Series 4A, 600V Plug N DriveTM Integrated Power Module for Energy Efficient Motor Drives |
| IRAMS06UP60B | Plug N Drive Integrated Power Module for Appliance Motor Drive |
| IRAMS10UP60APBF | Plug N Drive⑩ Integrated Power Module for Appliance Motor Drive |
| IRAMX16UP60B | Integrated Power Hybrid IC for Appliance Motor Drive Applications. 16A, 600V with Internal Shunt Resistor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IRADK31 | 功能描述:電源管理IC開發工具 1/4 HP DC brushless Mtr using IR31xx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| IRADK-S10UP60 | 制造商:International Rectifier 功能描述: |
| IRAE410 | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES |
| IRA-E410 | 制造商:MURATA 制造商全稱:Murata Manufacturing Co., Ltd. 功能描述:PYROELECTRIC INFRARED SENSORS IRA SERIES |
| IRA-E410QW1 | 制造商:Murata Manufacturing Co Ltd 功能描述:PYROELECTRIC INFRARED SENSOR - Bulk |
發布緊急采購，3分鐘左右您將得到回復。