- 您現在的位置：買賣IC網 > PDF目錄296207 > IR3628MTRPBF (International Rectifier) HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER PDF資料下載
參數資料
| 型號： | IR3628MTRPBF |
| 廠商： | International Rectifier |
| 英文描述： | HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER |
| 中文描述： | 高頻同步PWM降壓控制器 |
| 文件頁數： | 9/22頁 |
| 文件大小： | 581K |
| 代理商： | IR3628MTRPBF |
IR3628MPbF
08/10/2007
Programming the Current-Limit
The Current-Limit threshold can be set by
connecting a resistor (R
SET) from drain of low
side MOSFET to the OCSet pin. The resistor
can be calculated by using equation (3).
The
R
DS(on)
has
a
positive
temperature
coefficient and it should be considered for the
worse case operation. This resistor must be
placed close to the IC, place a location for small
ceramic capacitor from this pin to ground for
noise rejection purposes.
Ω
=
Ω
=
=
Ω
=
Ω
=
K
R
K
A
I
m
R
LIM
o
SET
on
DS
32
4
27
4
15
5
1
10
7
5
1
8
3
7
.
Select
.
R
current)
output
nominal
over
(50%
.
OCSet
)
(
)
(
)
3
--(
R
I
R
I
on
DS
OCSet
critical
L
SET
)
(
)
(
=
The inductor, output capacitor and the MOSFET
should be close to each other as possible. This
helps to reduce the EMI radiated by the power
traces due to the high switching currents through
them. Place input capacitor directly to the drain of
the high-side MOSFET, to reduce the ESR
replace the single input capacitor with two
parallel units.
The feedback part of the system should be kept
away from the inductor and other noise sources.
The critical
bypass components such as
capacitors for Vcc and Vc should be close to
respective pins. It is important to place the
feedback components include feedback resistors
and compensation components close to Fb and
Comp pins.
In multilayer PCB use one layer as power ground
plane and have a control circuit ground (analog
ground), to which all signals are referenced. The
goal is to localize the high current path to a
separate loop that does not interfere with the
more sensitive analog control function. These two
grounds must be connected together on the PC
board layout at a single point.
The MLPD is thermal enhanced package, based
on thermal performance it is recommended to
use 4-layers PCB. To effectively remove heat
from the device the exposed pad should be
connected to ground plane using vias.
Layout Consideration
The layout is very important when designing high
frequency switching converters. Layout will affect
noise pickup and can cause a good design to
perform with less than expected results.
Start to place the power components, make all
the connection in the top layer with wide, copper
filled areas.
17
相關PDF資料 |
PDF描述 |
|---|---|
| IR3629AMPBF | HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER WITH POWER GOOD OUTPUT |
| IR3629AMTRPBF | HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER WITH POWER GOOD OUTPUT |
| IR3629A | HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER WITH POWER GOOD OUTPUT |
| IR3629 | HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER WITH POWER GOOD OUTPUT |
| IR3810MPBF | HIGHLY INTEGRATED 12A WIDE-INPUT VOLTAGE, SYNCHRONOUS BUCK REGULATOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IR3629 | 制造商:IRF 制造商全稱:International Rectifier 功能描述:HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER WITH POWER GOOD OUTPUT |
| IR3629A | 制造商:IRF 制造商全稱:International Rectifier 功能描述:HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER WITH POWER GOOD OUTPUT |
| IR3629AMPBF | 制造商:IRF 制造商全稱:International Rectifier 功能描述:HIGH FREQUENCY SYNCHRONOUS PWM BUCK CONTROLLER WITH POWER GOOD OUTPUT |
| IR3629AMTRPBF | 功能描述:電壓模式 PWM 控制器 HI FREQ SYNC PWM 600kHz 5 or 12V 0.6 RoHS:否 制造商:Texas Instruments 輸出端數量:1 拓撲結構:Buck 輸出電壓:34 V 輸出電流: 開關頻率: 工作電源電壓:4.5 V to 5.5 V 電源電流:600 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:WSON-8 封裝:Reel |
| IR3629MPBF | 功能描述:IC CTLR PWM BUCK SYNC 12-MLPD RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,000 系列:- 應用:電源，ICERA E400，E450 輸入電壓:4.1 V ~ 5.5 V 輸出數:10 輸出電壓:可編程 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:42-WFBGA，WLCSP 供應商設備封裝:42-WLP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。