- 您現在的位置：買賣IC網 > PDF目錄384487 > IR2156SPbF (International Rectifier) BALLAST CONTROL IC PDF資料下載
參數資料
| 型號： | IR2156SPbF |
| 廠商： | International Rectifier |
| 英文描述： | BALLAST CONTROL IC |
| 中文描述： | 鎮流器控制IC |
| 文件頁數： | 19/24頁 |
| 文件大小： | 497K |
| 代理商： | IR2156SPBF |
IR2156
(S) & (PbF)
www.irf.com
19
Design Equations
Note: The results from the following design
equations can differ slightly from experimental
measurements due to IC tolerances, component
tolerances, and oscillator over- and under-shoot
due to internal comparator response time.
Step 1: Program Dead-time
The dead-time between the gate driver outputs
HO and LO is programmed with timing capacitor
CT and an internal dead-time resistor RDT. The
dead-time is the discharge time of capacitor CT
from 3/5VCC to 1/3VCC and is given as:
2000
=
T
DT
C
t
[Seconds]
(1)
or
2000
DT
T
t
C
=
[Farads]
(2)
Step 2: Program Run Frequency
The final run frequency is programmed with timing
resistor RT and timing capacitor CT. The charge
time of capacitor CT from 1/3VCC to 3/5VCC
determines the on-time of HO and LO gate driver
outputs. The run frequency is therefore given as:
)
2000
6
2
1
+
=
T
T
RUN
R
C
f
[Hertz] (3)
or
3333
12
.
1
=
RUN
T
T
f
C
R
[Ohms] (4)
Step 3: Program Preheat Frequency
The preheat frequency is programmed with timing
resistors RT and RPH, and timing capacitor CT.
The timing resistors are connected in parallel
internally for the duration of the preheat time. The
preheat frequency is therefore given as:
+
+
=
2000
6
2
1
PH
T
PH
T
T
PH
R
R
R
R
C
f
[Hertz] (5)
or
=
3333
12
.
1
3333
12
.
1
PH
T
T
T
PH
T
PH
f
C
R
R
f
C
R
[Ohms] (6)
Step 4: Program Preheat Time
The preheat time is defined by the time it takes
for the capacitor on pin CPH to charge up to 13
volts (assuming Vcc = 15 volts). An internal
current source of 4.3
μ
A flows out of pin CPH. The
preheat time is therefore given as:
[Seconds] (7)
or
[Farads] (8)
6
Step 5: Program Maximum Ignition Current
The maximum ignition current is programmed with
the external resistor RCS and an internal threshold
of 1.25 volts. This threshold determines the over-
current limit of the ballast, which can be exceeded
when the frequency ramps down towards
resonance during ignition and the lamp does not
6
02
.
e
C
t
PH
PH
=
331
.
=
e
t
C
PH
PH
相關PDF資料 |
PDF描述 |
|---|---|
| IR2159S | DIMMING BALLAST CONTROL IC |
| IR2171 | LINEAR CURRENT SENSING IC |
| IR2175 | LINEAR CURRENT SENSING IC |
| IR2175S | LINEAR CURRENT SENSING IC |
| IR2175SPBF | LINEAR CURRENT SENSING IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IR2156STR | 功能描述:IC BALLAST CONT 600V .5A 14-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
| IR2156STRPBF | 功能描述:功率驅動器IC Ballast Cntrl Prog Preht Tm & Run Freq RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| IR2157 | 制造商:IRF 制造商全稱:International Rectifier 功能描述:FULLY INTEGRATED BALLAST CONTROL IC |
| IR2157_07 | 制造商:IRF 制造商全稱:International Rectifier 功能描述:FULLY INTEGRATED BALLAST CONTROL IC |
| IR21571 | 功能描述:IC BALLAST CONTROL 16-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 照明，鎮流器控制器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 類型:CCFL 控制器 頻率:40 ~ 80 kHz 電流 - 電源:5mA 電流 - 輸出:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:16-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) 其它名稱:90-3991V+V01 |
發布緊急采購，3分鐘左右您將得到回復。