參數資料
| 型號： | IQ82C55A96 |
| 廠商： | Intersil |
| 文件頁數： | 2/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I/O EXPANDER 24B 44MQFP |
| 標準包裝： | 500 |
| 接口： | 可編程 |
| 輸入/輸出數： | 24 |
| 中斷輸出： | 無 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-QFP |
| 供應商設備封裝： | 44-MQFP（10x10） |
| 包裝： | 管件 |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
10
FN2969.10
November 16, 2006
INTR (Interrupt Request)
A “high” on this output can be used to interrupt the CPU
when an input device is requesting service. INTR is set by
the condition: STB is a “one”, IBF is a “one” and INTE is a
“one”. It is reset by the falling edge of RD. This procedure
allows an input device to request service from the CPU by
simply strobing its data into the port.
INTE A
Controlled by bit set/reset of PC4.
INTE B
Controlled by bit set/reset of PC2.
Output Control Signal Definition
(Figure 8 and 9)
OBF - (Output Buffer Full F/F). The OBF output will go “l(fā)ow”
to indicate that the CPU has written data out to the specified
port. This does not mean valid data is sent out of the port at
this time since OBF can go true before data is available.
Data is guaranteed valid at the rising edge of OBF, (See
Note 1). The OBF F/F will be set by the rising edge of the
WR input and reset by ACK input being low.
ACK - (Acknowledge Input). A “l(fā)ow” on this input informs the
82C55A that the data from Port A or Port B is ready to be
accepted. In essence, a response from the peripheral device
indicating that it is ready to accept data, (See Note 1).
INTR - (Interrupt Request). A “high” on this output can be
used to interrupt the CPU when an output device has
accepted data transmitted by the CPU. INTR is set when
ACK is a “one”, OBF is a “one” and INTE is a “one”. It is reset
by the falling edge of WR.
INTE A
Controlled by Bit Set/Reset of PC6.
INTE B
Controlled by Bit Set/Reset of PC2.
NOTE:
1. To strobe data into the peripheral device, the user must operate
the strobe line in a hand shaking mode. The user needs to send
OBF to the peripheral device, generates an ACK from the
peripheral device and then latch data into the peripheral device
on the rising edge of OBF.
FIGURE 7. MODE 1 (STROBED INPUT)
tST
STB
INTR
RD
INPUT FROM
IBF
PERIPHERAL
tSIB
tSIT
tPH
tPS
tRIT
tRIB
FIGURE 8. MODE 1 OUTPUT
1
D7
0
D6
1
D5
1
D4
1/0
D3 D2 D1 D0
CONTROL WORD
MODE 1 (PORT A)
PC7
8
ACKA
PC6
PA7-PA0
OBFA
INTRA
PC3
PC4, PC5
2
WR
PC4, PC5
1 = INPUT
0 = OUTPUT
1
D7 D6 D5 D4 D3 D2 D1 D0
CONTROL WORD
MODE 1 (PORT B)
PC1
8
ACKB
PC2
B
PB7-PB0
OBFB
INTRB
PC0
WR
10
INTE
A
82C55A
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9535ECDWR2G | 16-BIT I/O EXPANDER |
| IQ82C55A | IC I/O EXPANDER 24B 44MQFP |
| CQ82C55A96 | IC I/O EXPANDER 24B 44MQFP |
| CAT9554AWI-GT2 | IC I/O EXPANDER I2C 8B 16SOIC |
| CQ82C55A | IC I/O EXPANDER 24B 44MQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IQ82C55AZ | 功能描述:外圍驅動器與原件 - PCI PERI PRG-I/O 5V 8MHZ INDUSTRIAL TEMP RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| IQ82C55AZ96 | 功能描述:外圍驅動器與原件 - PCI PERI PRG-I/O 5V 8MHZ INDUSTRIAL TEMP RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
| IQ83C151C-12 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| IQ83C151C-16 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| IQ83C151C-20 | 制造商:TEMIC 制造商全稱:TEMIC Semiconductors 功能描述:CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
發(fā)布緊急采購，3分鐘左右您將得到回復。