- 您現在的位置：買賣IC網 > PDF目錄360867 > INSTALLATIONGUIDE Installation Guide - Socket A AMD Processor and Heatsink Installation Guide PDF資料下載
參數資料
| 型號： | INSTALLATIONGUIDE |
| 英文描述： | Installation Guide - Socket A AMD Processor and Heatsink Installation Guide |
| 中文描述： | 安裝指南- Socket A平臺AMD處理器和散熱器安裝指南 |
| 文件頁數： | 9/20頁 |
| 文件大?。?/td> | 1086K |
| 代理商： | INSTALLATIONGUIDE |
9
23986—December 2000
Socket A AMD Processor Installation Guide
9. Figure 9 shows the proper way to remove the plastic film from the phase-change
thermally conductive compound.
Note:
The phase-change thermal compound is very important to the efficiency and
success of the heatsink. The compound must be applied evenly to the surface of the
heatsink so it can (basically) melt and fill any microscopic voids in the surfaces of the
processor and heatsink with a thermally conductive material.
Caution:
If you have never installed a heat sink with this type of phase-change
thermal material, we suggest that you not remove this film until after you have
practiced installing the heatsink and mounting the clips on the socket. It may take a
few trials until you are familiar with the procedure. If you want to become familiar
with the process, skip the tape removal step for now and proceed to repeat Step 10
through Step 19.
Notice in Figure 9 that the film is removed by pulling rapidly at a right angle to
the base. A quick lifting motion is the best way to remove this film. Be aware that:
Once the film is removed, immediately install the heatsink.
The thermal compound must not come in contact with any foreign material.
Caution:
Do not remove the heatsink from the processor, once it has been
permanently installed. The phase-change thermal adhesive material cannot be
reused.
Remove the plastic film completely from the heatsink during the installation
to avoid causing the processor to overheat and be damaged when power is applied.
Pay strict attention to the procedures outlined in this document to avoid missing a
crucial step
.
Figure 9. Pull Tape from Thermal Material with a Quick Motion
相關PDF資料 |
PDF描述 |
|---|---|
| INSTRUCTIN603EWP | Optimizing the Instruction Execution on the 603e |
| INT201PFI1 | Interface IC |
| INT201TFI1 | Interface IC |
| INT2404G | LED BACKLIGHT FOR LCD DISPLAY |
| INT4003G | LED BACKLIGHT FOR LCD DISPLAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INSUL 2 DB-52P | 制造商:ITT 功能描述:MICRO 制造商:ITT Interconnect Solutions 功能描述:MICRO |
| INSUL 2 DE 19 SKT DOUBLE | 制造商:ITT 功能描述:MICRO 制造商:ITT Interconnect Solutions 功能描述:MICRO |
| INSUL 2 DE-19 PIN DBL DEN | 制造商:ITT 功能描述:MICRO 制造商:ITT Interconnect Solutions 功能描述:MICRO |
| INSUL ASSY CV3450-36-6 PIN | 制造商:ITT 功能描述:Circular 制造商:ITT Interconnect Solutions 功能描述:Circular |
| INSUL ASSY CV-R 36-10 PIN | 制造商:ITT Interconnect Solutions 功能描述:Circular |
發布緊急采購，3分鐘左右您將得到回復。