- 您現在的位置：買賣IC網 > PDF目錄360864 > INA2128PA microPower, Single-Supply, CMOS Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA2128PA |
| 元件分類： | 測量放大器 |
| 英文描述： | microPower, Single-Supply, CMOS Instrumentation Amplifier |
| 中文描述： | 微功耗，單電源，儀表放大器的CMOS |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 282K |
| 代理商： | INA2128PA |
INA2128
10
INPUT PROTECTION
The inputs of the INA2128 are individually protected for
voltages up to
±
40V. For example, a condition of –40V on
one input and +40V on the other input will not cause
damage. Internal circuitry on each input provides low series
impedance under normal signal conditions. To provide
equivalent protection, series input resistors would contribute
excessive noise. If the input is overloaded, the protection
circuitry limits the input current to a safe value of approxi-
mately 1.5 to 5mA. The typical performance curve “Input
Bias Current vs Common-Mode Input Voltage” shows this
input current limit behavior. The inputs are protected even if
the power supplies are disconnected or turned off.
CHANNEL CROSSTALK
The two channels of the INA2128 are completely indepen-
dent, including all bias circuitry. At DC and low frequency
there is virtually no signal coupling between channels.
Crosstalk increases with frequency and is dependent on
circuit gain, source impedance and signal characteristics.
As source impedance increases, careful circuit layout will
help achieve lowest channel crosstalk. Most crossstalk is
produced by capacitive coupling of signals from one channel
to the input section of the other channel. To minimize
coupling, separate the input traces as far as practical from
any signals associated with the opposite channel. A grounded
guard trace surrounding the inputs helps reduce stray cou-
pling between channels. Run the differential inputs of each
channel parallel to each other or directly adjacent on top and
bottom side of a circuit board. Stray coupling then tends to
produce a common-mode signal which is rejected by the
IA’s input.
FIGURE 5. Sum of Differences Amplifier.
FIGURE 4. Two-Axis Bridge Amplifier.
FIGURE 6. ECG Amplifier With Right-Leg Drive.
INA2128
1/2
R
G
/2
R
G
= 5.6k
V
O
LA
RL
RA
10k
Ref
NOTE: Due to the INA2128’s current-feedback
topology, V
is approximately 0.7V less than
the common-mode input voltage. This DC offset
in this guard potential is satisfactory for many
guarding applications.
G = 10
2.8k
V
G
V
G
2.8k
1/2
OPA2604
390k
390k
1/2
OPA2604
V
O
= G
A
(V
2
– V
1
) + G
B
(V
4
– V
3
)
V
1
V
2
Ref
V
3
R
GB
R
GA
V
4
Ref
INA2128
1/2
INA2128
1/2
X-axis
V
O
Y-axis
V
O
X-axis
Y-axis
V
EX
V
EX
INA2128
1/2
INA2128
1/2
相關PDF資料 |
PDF描述 |
|---|---|
| INA2128U | microPower, Single-Supply, CMOS Instrumentation Amplifier |
| INA2132 | Dual, Low Power, Single-Supply DIFFERENCE AMPLIFIER |
| INA2132U | Dual, Low Power, Single-Supply DIFFERENCE AMPLIFIER |
| INA2132UA | Dual, Low Power, Single-Supply DIFFERENCE AMPLIFIER |
| INA2133 | High-Speed. Precision Difference Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA2128U | 功能描述:差分放大器 Dual Low Power RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| INA2128U | 制造商:Texas Instruments 功能描述:IC SM AMP DUAL INSTRUMENTATION |
| INA2128U | 制造商:Texas Instruments 功能描述:AMP DUAL INSTRUMENTATION SMD 2128 |
| INA2128U/1K | 功能描述:差分放大器 Dual Low Power Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| INA2128U/1KE4 | 功能描述:差分放大器 Dual Low Power Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。