- 您現在的位置：買賣IC網 > PDF目錄360862 > INA116 Very High Accuracy Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA116 |
| 元件分類： | 測量放大器 |
| 英文描述： | Very High Accuracy Instrumentation Amplifier |
| 中文描述： | 極高精度儀表放大器 |
| 文件頁數： | 7/9頁 |
| 文件大?。?/td> | 246K |
| 代理商： | INA116 |
7
INA116
APPLICATIONS INFORMATION
Figure 1 shows the connections required for basic operation
of the INA116. Applications with noisy or high impedance
power supplies may require decoupling capacitors close to
the supply pins as shown.
The output is referred to the output reference (Ref) terminal
which is normally grounded. This must be a low impedance
connection to assure good common-mode rejection. A resis-
tance of 30
in series with this connection will cause a
typical device to degrade to approximately 72dB CMR at
G = 1.
SETTING THE GAIN
Gain of the INA116 is set by connecting a single external
resistor, R
G
, as shown. The gain is—
Commonly used gains and resistor values are shown in
Figure 1.
The 50k
term in equation 1 is the sum of the two feedback
resistors of A
1
and A
2
. These on-chip metal film resistors are
laser trimmed to accurate absolute values. The accuracy and
temperature coefficient of these resistors are included in the
gain accuracy and drift specifications of the INA116.
The stability and temperature drift of R
G
also affect gain.
R
G
’s contribution to gain accuracy and drift can be directly
inferred from the gain equation (1). Low resistor values
required for high gain make wiring resistance important.
Sockets add to the wiring resistance that will contribute
additional gain error in gains of approximately 100 or
greater.
OFFSET TRIMMING
The INA116 is laser trimmed for low offset voltage and
offset voltage drift; most applications require no external
offset adjustment. Figure 2 shows an optional circuit for
trimming the output offset voltage. A voltage applied to the
Ref terminal is summed at the output. Op amp A
1
provides
a low source impedance for the Ref terminal, assuring good
common-mode rejection.
G
=
1
+
50k
R
G
(1)
FIGURE 1. Basic Connections.
INA116
R
G
Also drawn in simplified form:
V
O
Ref
V
IN
–
V
IN
+
A
1
A
2
A
3
R
4
60k
R
3
60k
R
2
60k
R
1
60k
V
IN
V
IN
R
G
V–
INA116
V
O
Ref
G = 1 +50k
R
G
–
+
R
FB
25k
R
FB
25k
+1
+1
Over-Voltage
Protection
Over-Voltage
Protection
4
3
2
1
16
5
6
7
8
11
9
13
Input Guards
See Text.
0.1μF
V+
0.1μF
DESIRED
GAIN
1
2
5
10
20
50
100
200
500
1000
2000
5000
10000
NC: No Connection.
R
G
(
)
NC
50.00k
12.50k
5.556k
2.632k
1.02k
505.1
251.3
100.2
50.05
25.01
10.00
5.001
NEAREST 1% R
G
(
)
NC
49.9k
12.4k
5.62k
2.61k
1.02k
511
249
100
49.9
24.9
10
4.99
相關PDF資料 |
PDF描述 |
|---|---|
| INA116P | Very High Accuracy Instrumentation Amplifier |
| INA116U | Very High Accuracy Instrumentation Amplifier |
| INA117KU | High Common-Mode Voltage DIFFERENCE AMPLIFIER |
| INA117AM | High Common-Mode Voltage DIFFERENCE AMPLIFIER |
| INA117BM | High Common-Mode Voltage DIFFERENCE AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA116P | 制造商:BB 制造商全稱:BB 功能描述:Ultra Low Input Bias Current INSTRUMENTATION AMPLIFIER |
| INA116PA | 功能描述:儀表放大器 Ultra Low Input Bias Current RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA116PA | 制造商:Texas Instruments 功能描述:IC AMP INSTRUMENTATION DIP16 116 |
| INA116PAG4 | 功能描述:儀表放大器 Ultra Low Input Bias Current RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA116U | 制造商:BB 制造商全稱:BB 功能描述:Ultra Low Input Bias Current INSTRUMENTATION AMPLIFIER |
發布緊急采購，3分鐘左右您將得到回復。