- 您現在的位置：買賣IC網 > PDF目錄360862 > INA115 Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA115 |
| 元件分類： | 測量放大器 |
| 英文描述： | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| 中文描述： | 單電源，軌至軌，低成本儀表放大器 |
| 文件頁數： | 8/11頁 |
| 文件大小： | 211K |
| 代理商： | INA115 |
8
INA115
APPLICATION INFORMATION
Figure 1 shows the basic connections required for operation of
the INA115. Applications with noisy or high impedance
power supplies may require decoupling capacitors close to the
device pins as shown.
The output is referred to the output reference (Ref) terminal
which is normally grounded. This must be a low-impedance
connection to assure good common-mode rejection. A resis-
tance of 5
in series with the Ref pin will cause a typical
device to degrade to approximately 80dB CMR (G=1).
The INA115 has a separate output sense feedback connection
(pin 12). Pin 12 must be connected (normally to the output
terminal, pin 11) for proper operation. The output sense
connection can be used to sense the output voltage directly at
the load for best accuracy.
SETTING THE GAIN
Gain of the INA115 is set by connecting a single external
resistor, R
G
:
FIGURE 1. Basic Connections.
DESIRED
GAIN
R
G
(
)
NEAREST 1% R
G
(
)
1
2
5
10
20
50
100
200
500
1000
2000
5000
10000
No Connection
50.00k
12.50k
5.556k
2.632k
1.02k
505.1
251.3
100.2
50.05
25.01
10.00
5.001
No Connection
49.9k
12.4k
5.62k
2.61k
1.02k
511
249
100
49.9
24.9
10
4.99
G
=
1
+
50 k
R
G
(1)
Commonly used gains and resistor values are shown in
Figure 1.
For G=1, no resistor is required, but connect pins 2-3 and
connect pins 14-15. Gain peaking in G=1 can be reduced by
shorting the internal 25k
feedback resistors (see typical
performance curve Gain vs Frequency). To do this, connect
pins 1-2-3 and connect pins 8-14-15.
The 50k
term in equation 1 comes from the sum of the two
internal feedback resistors. These are on-chip metal film
resistors which are laser trimmed to accurate absolute values.
The accuracy and temperature coefficient of these resistors
are included in the gain accuracy and drift specifications of the
INA115.
The stability and temperature drift of the external gain setting
resistor, R
, also affects gain. R
’s contribution to gain error
and drift can be directly inferred from the gain equation (1).
Low resistor values required for high gain can make wiring
resistance important. The “force and sense” type connections
illustrated in Figure 1 help reduce the effect of interconnection
resistance.
A
1
A
2
A
3
12
11
10
25k
25k
25k
25k
13
7
5
4
V
IN
V
IN
R
G
V+
V–
INA115
–
+
Over-Voltage
Protection
25k
25k
Over-Voltage
Protection
15
14
3
2
8
V
O2
V
O1
1
Load
G = 1 +50k
R
G
V
O
= G (V
IN
– V
IN
)
0.1μF
0.1μF
+
–
V
O
Also drawn in simplified form:
Ref
INA115
V
IN
V
IN
R
G
–
+
V
O
V
O2
V
O1
相關PDF資料 |
PDF描述 |
|---|---|
| INA116PA | Very High Accuracy Instrumentation Amplifier |
| INA116UA | MOSFET N-CH 450V 7A TO-220D |
| INA116 | Very High Accuracy Instrumentation Amplifier |
| INA116P | Very High Accuracy Instrumentation Amplifier |
| INA116U | Very High Accuracy Instrumentation Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA115AU | 功能描述:儀表放大器 Precision Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA115AU/1K | 功能描述:儀表放大器 Precision Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA115AU/1KE4 | 功能描述:儀表放大器 Precision Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA115AU-1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| INA115AU-1/1K | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。