- 您現在的位置：買賣IC網 > PDF目錄360861 > INA101CM Precision Gain of 5 Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA101CM |
| 元件分類： | 測量放大器 |
| 英文描述： | Precision Gain of 5 Instrumentation Amplifier |
| 中文描述： | 5精密增益儀表放大器 |
| 文件頁數： | 5/6頁 |
| 文件大?。?/td> | 91K |
| 代理商： | INA101CM |
INA101
5
INPUT NOISE VOLTAGE
vs FREQUENCY (100
≤
GAIN
≤
1000)
Frequency (Hz)
I
√
H
0
1000
100
10
1
10
100
1000
OUTPUT NOISE vs GAIN
Gain (V/V)
O
0
30
20
10
0
10
100
1000
R
S
= 1M
R
S
= 1000k
R
S
= 10k
R
S
= 0
SETTLING TIME vs GAIN
Gain (V/V)
S
1
100
1000
10
1000
100
10
1%
R
= 2k
C
L
= 1000pF
0.01%
0.1%
(1)
G = 1 +
TYPICAL PERFORMANCE CURVES
(CONT)
At +25
°
C, V
CC
=
±
15V unless otherwise noted.
40k
R
G
APPLICATION INFORMATION
Figure 1 shows the basic connections required for operation
of the INA101. (Pin numbers shown are for the TO-100
metal package.) Applications with noisy or high impedance
power supplies may require decoupling capacitors close to
the device pins as shown.
The output is referred to the output Common terminal which
is normally grounded. This must be a low-impedance con-
nection to assure good common-mode rejection. A resis-
tance greater than 0.1
in series with the Common pin will
cause common-mode rejection to fall below 106dB.
SETTING THE GAIN
Gain of the INA101 is set by connecting a single external
resistor, R
G
:
The 40k
term in equation (1) comes from the sum of the
two internal feedback resistors. These are on-chip metal film
resistors which are laser trimmed to accurate absolute val-
ues. The accuracy and temperature coefficient of these
resistors are included in the gain accuracy and drift specifi-
cations of the INA101.
The stability and temperature drift of the external gain
setting resistor, R
G
, also affects gain. R
G
’s contribution to
gain accuracy and drift can be directly inferred from the gain
equation (1). Low resistor values required for high gain can
make wiring resistance important. Sockets add to the wiring
resistance which will contribute additional gain error (possi-
bly an unstable gain error) in gains of approximately 100 or
greater. The gain sense connections on the DIP and SOL-16
packages (see Figure 2) reduce the gain error produced by
wiring or socket resistance.
相關PDF資料 |
PDF描述 |
|---|---|
| INA101 | Precision Gain of 5 Instrumentation Amplifier |
| INA101HP | Precision Gain of 5 Instrumentation Amplifier |
| INA101KU | Precision Gain of 5 Instrumentation Amplifier |
| INA101SG | Precision Gain of 5 Instrumentation Amplifier |
| INA101SM | Precision Gain of 5 Instrumentation Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA101HP | 功能描述:儀表放大器 Very High Accuracy Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA101HP | 制造商:BURR-BROWN 功能描述:IC AMP INSTRUMENTATION DIP14 101 |
| INA101HP-1 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| INA101HPG4 | 功能描述:儀表放大器 Very High Accuracy Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA101KU | 功能描述:儀表放大器 Very High Accuracy Instrumentation Amp RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。