- 您現在的位置：買賣IC網 > PDF目錄360850 > IMIC9630 Clocks and Buffers PDF資料下載
參數資料
| 型號： | IMIC9630 |
| 英文描述： | Clocks and Buffers |
| 中文描述： | 時鐘和緩沖器 |
| 文件頁數： | 6/10頁 |
| 文件大小： | 125K |
| 代理商： | IMIC9630 |
C9530
Document #: 38-07033 Rev. *B
Page 6 of 10
As an example and using this formula for this data sheet’s
device, a design that has no discrete loading capacitors
(C
DISC
) and each of the crystal device PCB traces has a
capacitance (C
PCB
) to ground of 4 pF (typical value) would
calculate as follows.
Therefore, to obtain output frequencies that are as close to this
data sheets specified values as possible, in this design
example, you should specify a parallel cut crystal that is
designed to work into a load of 20 pF.
Spread Spectrum Clocking
Down Spread Description
Spread Spectrum is a modulation technique for distributing
clock period over a certain bandwidth (called Spread
Bandwidth). This technique allows the distribution of the
undesirable electromagnetic energy (EMI) over a wide range
of frequencies therefore reducing the average radiated energy
present at any frequency over a given time period. As the
spread is specified as a percentage of the resting (non-spread)
frequency value, it is effective at the fundamental and, to a
greater extent, at all it's harmonics.
In this device, Spread Spectrum is enabled externally through
pin 27 (SSCG#) or internally via SMBus Byte 0 Bit 0 and 6.
Spread spectrum is enabled externally when the SSCG# pin
is low. This pin has an internal device pull up resistor, which
causes its state to default to a high (Spread Spectrum
disabled) unless externally forced to a low. It may also be
enabled by programming SMBus Byte 0 Bit 0 LOW (to enable
SMBus control of the function) and then programming SMBus
Byte 0 Bit 6 LOW to set the feature active.
C
XINPCB
C
XOUTPCB
C
XOUTDISC
C
XINDISC
C
XINFTG
C
XOUTFTG
XIN
XOUT
Clock Generator
(4 pF + 36 pF + 0 pF)
x
(4 pF + 36 pF + 0 pF)
(4 pF + 36 pF + 0 pF)
x
(4 pF + 36 pF + 0 pF)
C
L
=
40 x 40
40 x 40
=
=
1600
80
= 20 pF
Table 7. Spectrum Spreading Selection Table
[7]
Output Clock Frequency
33.3 MHz (XIN)
66.6 MHz (XIN*2)
100.0 MHz (XIN*3)
133.3 MHz (XIN*4)
% of Frequency Spreading
Mode
SMBus Byte 0 Bit 5 = 0
1.0% (–1.0% + 0%)
1.0% (–1.0% + 0%)
1.0% (–1.0% + 0%)
1.0% (–1.0% + 0%)
SMBus Byte 0 Bit 5 = 1
0.5% (–0.5% + 0%)
0.5% (–0.5% + 0%)
0.5% (–0.5% + 0%)
0.5% (–0.5% + 0%)
Down Spread
Down Spread
Down Spread
Down Spread
Note:
7.
When SSCG is enabled, the device will down spread the clock over a range that is 1% of its resting frequency. This means that for a 100-MHz output clock
frequency will sweep through a spectral range from 99 to 100 MHz.
S p re a d o ff
S p re a d o n
C e n te r F re q u e n c y ,
S p re a d o ff
C e n te r F re q u e n c y ,
S p re a d o n
Figure 1. Spread Spectrum
相關PDF資料 |
PDF描述 |
|---|---|
| IMIC9827H | Clocks and Buffers |
| IMIC9850A | Clocks and Buffers |
| IMIC9870G | Clocks and Buffers |
| IMIC9950 | Clocks and Buffers |
| IMICT266DZB | Voltage-Controlled Oscillator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IMIC9701 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low EMI Clock Generator for Pentium II Systems with Power Management |
| IMIC9701AYB | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Low EMI Clock Generator for Pentium II Systems with Power Management |
| IMIC9714 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:100 MHz Clock Generator with SSCG and Power Management for Mobile Application |
| IMIC9714AT | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:100 MHz Clock Generator with SSCG and Power Management for Mobile Application |
| IMIC9714AY | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:100 MHz Clock Generator with SSCG and Power Management for Mobile Application |
發布緊急采購，3分鐘左右您將得到回復。