3
Absolute Maximum Ratings
Thermal Information
V+ to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <36V
V+ to V
D
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
V
D
to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
V
D
to V
S
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <
±
22V
V
L
to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <33V
V
L
to V
IN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <30V
V
L
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <20V
V
IN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . <20V
Current (Any Terminal). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Operating Conditions
Temperature Range. . . . . . . . . . . . . . . . . . . . . . . . . -55
o
C to 125
o
C
Thermal Resistance (Typical, Note 1)
CERDIP Package. . . . . . . . . . . . . . . . .
Maximum Junction Temperature
CERDIP Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
o
C
Maximum Storage Temperature. . . . . . . . . . . . . . . . -65
o
C to 150
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300
o
C
θ
JA
(
o
C/W)
75
θ
JC
(
o
C/W)
18
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1.
θ
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
V+ = +15V, V- = -15V, V
L
= +5V
PER CHANNEL PARAMETER
TEST CONDITIONS
(NOTES 3, 5)
25
o
C
UNITS
-55
o
C
125
o
C
DYNAMIC CHARACTERISTICS
Turn ON Time, t
ON
R
L
= 1k
, V
ANALOG
= -10V
to +10V; (Figure 6, Note 4)
-
-
500
ns
Turn OFF Time, t
OFF
-
-
250
ns
Charge Injection, Q
Figure 5
-
10 (Typ)
-
mV
OFF Isolation, OIRR
f = 1MHz, R
L
= 100
,
C
L
≤
5pF (Figure 3)
-
54 (Typ)
-
dB
Crosstalk, CCRR
Figure 2
-
-54 (Typ)
-
dB
DIGITAL INPUT CHARACTERISTICS
Input Logic Current, I
IN(ON)
V
IN
= 2.4V (Note 2)
±
1
±
1
±
10
μ
A
Input Logic Current, I
IN(OFF)
V
IN
= 0.8V (Note 2)
±
1
±
1
±
10
μ
A
ANALOG SWITCH CHARACTERISTICS
Drain-Source ON Resistance, r
DS(ON)
Channel-to-Channel r
DS(ON)
Match,
r
DS(ON)
V
D
=
±
10V, I
S
= -10mA
25
25
50
-
10 (Typ)
-
Minimum Analog Signal Handling Capability, V
ANALOG
-
±
14 (Typ)
-
V
Switch OFF Leakage Current, I
D(OFF)
, I
S(OFF)
V
ANALOG
= -10V to +10V
-
±
1.0
100
nA
Switch ON Leakage Current, I
D(ON)
+I
S(ON)
V
D
= V
S
= -10V to +10V
-
±
1.0
100
nA
POWER SUPPLY CHARACTERISTICS
+ Power Supply Quiescent Current, I+
10
10
100
μ
A
- Power Supply Quiescent Current, I-
10
10
100
μ
A
+5V Supply Quiescent Current, I
L
10
10
100
μ
A
Ground Quiescent Current, I
GND
10
10
100
μ
A
NOTES:
2. Some channels are turned on by high (1) logic inputs and other channels are turned on by low (0) inputs; however 0.8V to 2.4V describes the
minimum range for switching properly. Refer to logic diagrams to find logical value of logic input required to produce ON or OFF state.
3. Typical values are for design aid only, not guaranteed or production tested.
4. For IH5151 devices, channels which are off for logic input
≥
2.4V (Pins 3 and 4, 5 and 6) have slower t
ON
time, than channels on Pins 1, 16 and 8, 9.
This is done so switch will maintain break-before-make action when connected in DT configuration, i.e., Pin 1 connected in Pin 3.
5. Min or Max value, unless otherwise specified.
IH5151