- 您現在的位置：買賣IC網 > PDF目錄9058 > IDT5V50013DCG8 (IDT, Integrated Device Technology Inc)IC CLK GENERATOR LOW EMI 8-SOIC PDF資料下載
參數資料
| 型號： | IDT5V50013DCG8 |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 3/8頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLK GENERATOR LOW EMI 8-SOIC |
| 標準包裝： | 2,500 |
| 類型： | 時鐘發生器 |
| PLL： | 是 |
| 輸入： | 時鐘 |
| 輸出： | 時鐘 |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:1 |
| 差分 - 輸入:輸出： | 無/無 |
| 頻率 - 最大： | 140MHz |
| 除法器/乘法器： | 無/無 |
| 電源電壓： | 3 V ~ 3.63 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 5V50013DCG8 |
IDT5V50013
LOW EMI CLOCK GENERATOR
SSCG
IDT LOW EMI CLOCK GENERATOR
3
IDT5V50013
REV G 072412
External Components
The IDT5V50013 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01F must be connected
between VDD and GND on pins 2 and 3, as close to these
pins as possible. For optimum device performance, the
decoupling capacitor should be mounted on the component
side of the PCB. Avoid the use of vias in the decoupling
circuit.
Series Termination Resistor
When the PCB trace between the clock output and the load
is over 1 inch, series termination should be used. To series
terminate a 50
Ω trace (a commonly used trace impedance)
place a 33
Ωresistor in series with the clock line, as close to
the clock output pin as possible. The nominal impedance of
the clock output is 20
Ω.
PCB Layout Recommendations
For optimum device performance and lowest output phase
noise, the following guidelines should be observed.
1) The 0.01F decoupling capacitor should be mounted on
the component side of the board as close to the VDD pin as
possible. No vias should be used between the decoupling
capacitor and VDD pin. The PCB trace to VDD pin should
be kept as short as possible, as should the PCB trace to the
ground via.
2) To minimize EMI, the 33
Ω series termination resistor (if
needed) should be placed close to the clock output.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through other signal
layers. Other signal traces should be routed away from the
IDT5V50013. This includes signal traces just underneath
the device, or on layers adjacent to the ground plane layer
used by the device.
Spread Spectrum Profile
The IDT5V50013 low EMI clock generator uses an
optimized frequency slew rate algorithm to facilitate down
stream tracking of zero delay buffers and other PLL devices.
The frequency modulation amplitude is constant with
variations of the input frequency.
Time
Fr
eq
ue
ncy
Modulation Rate
相關PDF資料 |
PDF描述 |
|---|---|
| VI-21T-MW-S | CONVERTER MOD DC/DC 6.5V 100W |
| ICS650R-22LFT | IC CLK SOURCE PRV/STB 20-SSOP |
| VE-23Z-MU-S | CONVERTER MOD DC/DC 2V 80W |
| SL15303EZIT | IC CLOCK SSCG 1PLL 8TSSOP |
| VE-23Y-MU-S | CONVERTER MOD DC/DC 3.3V 132W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT5V50015DCG | 功能描述:IC CLK GENERATOR LOW EMI 8SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| IDT5V50015DCG8 | 制造商:Integrated Device Technology Inc 功能描述:IC CLK GENERATOR LOW EMI 8SOIC |
| IDT5V50015PGG | 功能描述:IC CLK GENERATOR LOW EMI 8TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
| IDT5V50015PGG8 | 制造商:Integrated Device Technology Inc 功能描述:IC CLK GENERATOR LOW EMI 8TSSOP |
| IDT5V50017DCG | 功能描述:IC CLK GENERATOR LOW EMI 8SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS，LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP（7x7） 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。