- 您現在的位置：買賣IC網 > PDF目錄383097 > ICX409AL (Sony Corporation) Diagonal 6mm (Type 1/3) CCD Image Sensor for CCIR B/W Video Cameras PDF資料下載
參數資料
| 型號： | ICX409AL |
| 廠商： | Sony Corporation |
| 英文描述： | Diagonal 6mm (Type 1/3) CCD Image Sensor for CCIR B/W Video Cameras |
| 中文描述： | 對角線6毫米（類型1 / 3）CCD圖像傳感器的無線電咨詢委員會/黑白視頻攝像機 |
| 文件頁數： | 9/17頁 |
| 文件大?。?/td> | 172K |
| 代理商： | ICX409AL |
–
9
–
ICX409AL
Image Sensor Characteristics Measurement Method
Measurement conditions
1) In the following measurements, the device drive conditions are at the typical values of the bias and clock
voltage conditions.
2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical
black (OB) level is used as the reference for the signal output, and the value measured at point [
A] in the
drive circuit example is used.
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance: 706cd/m
2
, color temperature of 3200K halogen source) as a subject.
(Pattern for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut
filter and image at F8. The luminous intensity to the sensor receiving surface at this point is defined as the
standard sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the signal output (Vs) at the center of the screen and substitute the value into the
following formula.
2. Saturation signal
Set to standard imaging condition
II
. After adjusting the luminous intensity to 10 times the intensity with the
average value of the signal output, 200mV, measure the minimum value of the signal output.
3. Smear
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with the average value of the signal output, 200mV. When the readout clock is
stopped and the charge drain is executed by the electronic shutter at the respective H blankings, measure
the maximum value (VSm [mV]) of the signal output and substitute the value into the following formula.
S = Vs
×
[mV]
50
250
Sm = 20
×
log
[dB] (1/10V method conversion value)
×
×
500
1
200
YSm
10
1
相關PDF資料 |
PDF描述 |
|---|---|
| ICX412 | Timing Generator and Signal Processor for Frame Readout CCD Image Sensor |
| ICX412AQF | Diagonal 8.933mm (Type 1/1.8) Frame Readout CCD Image Sensor with a Square Pixel for Color Cameras |
| ICX414AL | Diagonal 8mm Progressive Scan CCD Solid-state Image Sensor with Square Pixel for EIA B/W Cameras |
| ICX418AKL | Diagonal 8mm (Type 1/2) CCD Image Sensor for NTSC Color Video Cameras |
| ICX418ALL | Diagonal 8mm (Type 1/2) CCD Image Sensor for EIA B/W Video Cameras |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICX411AQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Diagonal 8.98mm(Type 1/1.8) Frame Readout CCDImage Sensor with a Square Pixel for Color Cameras |
| ICX412 | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Timing Generator for Frame Readout CCD Image Sensor |
| ICX412AQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Diagonal 8.933mm(Type 1/1.8) Frame Readout CCDImage Sensor with a Square Pixel for Color Cameras |
| ICX412AQF | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 8.933mm (Type 1/1.8) Frame Readout CCD Image Sensor with a Square Pixel for Color Cameras |
| ICX413AQ | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Diagonal 28.40mm(Type 1.8) Frame Readout CCDImage Sensor with Square Pixel for Color Cameras |
發布緊急采購，3分鐘左右您將得到回復。