參數資料
型號: ICX405AL
廠商: Sony Corporation
英文描述: Diagonal 6mm (Type 1/3) CCD Image Sensor for CCIR B/W Video Cameras(對角線式、3毫米(1/6型)CCD圖像傳感器(用于CCIR黑白攝像機))
中文描述: 對角線6毫米(類型1 / 3)CCD圖像傳感器的無線電咨詢委員會/黑白攝像機(對角線式,3毫米(1 / 6型)防治荒漠化圖像傳感器(用于無線電咨詢委員會黑白攝像機))
文件頁數: 15/17頁
文件大?。?/td> 168K
代理商: ICX405AL
15
ICX405AL
Notes on Handling
1) Static charge prevention
CCD image sensors are easily damaged by static discharge. Before handling be sure to take the following
protective measures.
a) Either handle bare handed or use non-chargeable gloves, clothes or material.
Also use conductive shoes.
b) When handling directly use an earth band.
c) Install a conductive mat on the floor or working table to prevent the generation of static electricity.
d) Ionized air is recommended for discharge when handling CCD image sensor.
e) For the shipment of mounted substrates, use boxes treated for the prevention of static charges.
2) Soldering
a) Make sure the package temperature does not exceed 80
°
C.
b) Solder dipping in a mounting furnace causes damage to the glass and other defects. Use a ground 30W
soldering iron and solder each pin in less than 2 seconds. For repairs and remount, cool sufficiently.
c) To dismount an image sensor, do not use a solder suction equipment. When using an electric desoldering
tool, use a thermal controller of the zero cross On/Off type and connect it to ground.
3) Dust and dirt protection
Image sensors are packed and delivered by taking care of protecting its glass plates from harmful dust and
dirt. Clean glass plates with the following operation as required, and use them.
a) Perform all assembly operations in a clean room (class 1000 or less).
b) Do not either touch glass plates by hand or have any object come in contact with glass surfaces. Should
dirt stick to a glass surface, blow it off with an air blower. (For dirt stuck through static electricity ionized
air is recommended.)
c) Clean with a cotton bud and ethyl alcohol if the grease stained. Be careful not to scratch the glass.
d) Keep in a case to protect from dust and dirt. To prevent dew condensation, preheat or precool when
moving to a room with great temperature differences.
e) When a protective tape is applied before shipping, just before use remove the tape applied for
electrostatic protection. Do not reuse the tape.
4) Installing (attaching)
a) Remain within the following limits when applying a static load to the package. Do not apply any load more
than 0.7mm inside the outer perimeter of the glass portion, and do not apply any load or impact to limited
portions. (This may cause cracks in the package.)
Compressive strength
Cover glass
AAAA
Plastic package
1.2Nm
Torsional strength
AAAA
AAAA
AAAA
AAAA
AAAA
相關PDF資料
PDF描述
ICX406AQF Diagonal 8.98mm (Type 1/1.8) Frame Readout CCD Image Sensor with a Square Pixel for Color Cameras
ICX406 Timing Generator and Signal Processor for Frame Readout CCD Image Sensor
ICX408AK Diagonal 6mm (Type 1/3) CCD Image Sensor for NTSC Color Video Cameras(對角線式、3毫米(1/6型)CCD圖像傳感器(用于NTSC彩色攝像機))
ICX408AL Diagonal 6mm (Type 1/3) CCD Image Sensor for EIA B/W Video Cameras
ICX409AK Diagonal 6mm (Type 1/3) CCD Image Sensor for PAL Color Video Cameras(對角線式、3毫米(1/6型)CCD圖像傳感器(用于PAL彩色攝像機))
相關代理商/技術參數
參數描述
ICX406 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Timing Generator and Signal Processor for Frame Readout CCD Image Sensor
ICX406AQ 制造商:SONY 制造商全稱:Sony Corporation 功能描述:ICX406AQ工作、原理
ICX406AQF 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 8.98mm (Type 1/1.8) Frame Readout CCD Image Sensor with a Square Pixel for Color Cameras
ICX406BQ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CCD IMAGE SENSOR Diag. 8.98mm (Type 1/1.8) Frame Readout CCD Image Sensor w/Square Pixel for Color Cameras (33 pages 345K Rev. E01327-PS same as AQ different mfg. location)
ICX406BQF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:CCD IMAGE SENSOR Diag. 8.98mm (Type 1/1.8) Frame Readout CCD Image Sensor w/Square Pixel for Color Cameras (33 pages 349K Rev. E01331-PS same as AQF different mfg. location)