- 您現在的位置：買賣IC網 > PDF目錄383097 > ICX404AL (Sony Corporation) Diagonal 6mm (Type 1/3) CCD Image Sensor for EIA B/W Video Cameras(對角線式、3毫米(1/6型)CCD圖像傳感器（用于EIA黑白攝像機）) PDF資料下載
參數資料
| 型號： | ICX404AL |
| 廠商： | Sony Corporation |
| 英文描述： | Diagonal 6mm (Type 1/3) CCD Image Sensor for EIA B/W Video Cameras(對角線式、3毫米(1/6型)CCD圖像傳感器（用于EIA黑白攝像機）) |
| 中文描述： | 對角線6毫米（類型1 / 3）CCD圖像傳感器的環境影響評估/黑白攝像機（對角線式，3毫米（1 / 6型）防治荒漠化圖像傳感器（用于評估黑白攝像機）） |
| 文件頁數： | 9/17頁 |
| 文件大小： | 167K |
| 代理商： | ICX404AL |
ICX404AL
Image Sensor Characteristics Measurement Method
Measurement conditions
1) In the following measurements, the device drive conditions are at the typical values of the bias and clock
voltage conditions.
2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical
black (OB) level is used as the reference for the signal output, and the value measured at point [
A] in the
drive circuit example is used.
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance: 706cd/m
2
, color temperature of 3200K halogen source) as a subject.
(Pattern for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut
filter and image at F8. The luminous intensity to the sensor receiving surface at this point is defined as the
standard sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the signal output (Vs
)
at the center of the screen and substitute the value into the following
formula.
2. Saturation signal
Set to standard imaging condition
II
. After adjusting the luminous intensity to 10 times the intensity with the
average value of the signal output, 200mV, measure the minimum value of the signal output.
3. Smear
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with average value of the signal output, 200mV. When the readout clock is stopped
and the charge drain is executed by the electronic shutter at the respective H blankings, measure the
maximum value YSm [mV] of the signal output and substitute the value into the following formula.
S = Vs
×
[mV]
60
250
Sm = 20
×
log
[dB] (1/10V method conversion value)
×
×
500
1
200
VSm
10
1
–
9
–
相關PDF資料 |
PDF描述 |
|---|---|
| ICX405AK | Diagonal 6mm (Type 1/3) CCD Image Sensor for PAL Color Video Cameras(對角線式、3毫米(1/6型)CCD圖像傳感器（用于PAL彩色攝像機）) |
| ICX405AL | Diagonal 6mm (Type 1/3) CCD Image Sensor for CCIR B/W Video Cameras(對角線式、3毫米(1/6型)CCD圖像傳感器（用于CCIR黑白攝像機）) |
| ICX406AQF | Diagonal 8.98mm (Type 1/1.8) Frame Readout CCD Image Sensor with a Square Pixel for Color Cameras |
| ICX406 | Timing Generator and Signal Processor for Frame Readout CCD Image Sensor |
| ICX408AK | Diagonal 6mm (Type 1/3) CCD Image Sensor for NTSC Color Video Cameras(對角線式、3毫米(1/6型)CCD圖像傳感器（用于NTSC彩色攝像機）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICX405AK | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 6mm (Type 1/3) CCD Image Sensor for PAL Color Video Cameras |
| ICX405AL | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Diagonal 6mm(Type 1/3) CCD Image Sensor forCCIR B/W Video Cameras |
| ICX406 | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Timing Generator and Signal Processor for Frame Readout CCD Image Sensor |
| ICX406AQ | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:ICX406AQ工作、原理 |
| ICX406AQF | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 8.98mm (Type 1/1.8) Frame Readout CCD Image Sensor with a Square Pixel for Color Cameras |
發布緊急采購，3分鐘左右您將得到回復。