- 您現在的位置：買賣IC網 > PDF目錄383097 > ICX278AL (Sony Corporation) Diagonal 4.5mm (Type 1/4) CCD Image Sensor for EIA B/W Video Cameras PDF資料下載
參數資料
| 型號： | ICX278AL |
| 廠商： | Sony Corporation |
| 英文描述： | Diagonal 4.5mm (Type 1/4) CCD Image Sensor for EIA B/W Video Cameras |
| 中文描述： | 對角線4.5毫米（類型1 / 4）CCD圖像傳感器的環(huán)境影響評估/黑白視頻攝像機 |
| 文件頁數： | 10/19頁 |
| 文件大?。?/td> | 203K |
| 代理商： | ICX278AL |
–
10
–
ICX278AK
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance 706cd/m
2
, color temperature of 3200K halogen source) as a subject. (Pattern
for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter
and image at F5.6. The luminous intensity to the sensor receiving surface at this point is defined as the
standard sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
3) Standard imaging condition
III
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens (exit pupil distance
–
33mm) with CM500S (t = 1.0mm) as an IR cut filter. The
luminous intensity is adjusted to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the Y signal (Ys) at the center of the screen and substitute the value into the following
formula.
S = Ys
×
250
2. Sensitivity ratio
Set to standard imaging condition
II
. Adjust the luminous intensity so that the average value of the Y signal
output is 200mV, and then measure the Mg signal output (S
Mg
[mV]) and G signal output (S
G
[mV]), and Ye
signal output (S
Ye
[mV]) and Cy signal output (S
Cy
[mV]) at the center of the screen with frame readout
method. Substitute the values into the following formula.
R
MgG
= S
Mg
/
SG
R
YeCy
= S
Ye
/S
Cy
3. Saturation signal
Set to standard imaging condition
II
. After adjusting the luminous intensity to 10 times the intensity with
average value of the Y signal output, 200mV, measure the minimum value of the Y signal.
4. Smear
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with average value of the Y signal output, 200mV. When the readout clock is stopped
and the charge drain is executed by the electronic shutter at the respective H blankings, measure the
maximum value (YSm [mV]) of the Y signal output and substitute the value into the following formula.
Sm = 20
×
log YSm
×
×
1
10
500
200
60
1
相關PDF資料 |
PDF描述 |
|---|---|
| ICX279AK | Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras |
| ICX279AL | Diagonal 4.5mm (Type 1/4) CCD Image Sensor for CCIR B/W Video Cameras |
| ICX282AKF | Diagonal 11mm (Type 2/3) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
| ICX282 | Timing Generator for Frame Readout CCD Image Sensor |
| ICX282AQ | Diagonal 11mm (Type 2/3) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICX279AK | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras |
| ICX279AL | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for CCIR B/W Video Cameras |
| ICX282 | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Timing Generator for Frame Readout CCD Image Sensor |
| ICX282AK | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 11mm (Type 2/3) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
| ICX282AKF | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 11mm (Type 2/3) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras |
發(fā)布緊急采購，3分鐘左右您將得到回復。