參數資料
型號: ICX258AL
廠商: Sony Corporation
英文描述: Diagonal 6mm (Type 1/3) CCD Image Sensor for EIA B/W Video Cameras(對角線式、6毫米(1/3型)CCD圖像傳感器(用于EIA黑白攝像機))
中文描述: 對角線6毫米(類型1 / 3)CCD圖像傳感器的環境影響評估/黑白攝像機(對角線式,6毫米(1 / 3型)防治荒漠化公約圖像傳感器(用于評估黑白攝像機))
文件頁數: 9/17頁
文件大?。?/td> 183K
代理商: ICX258AL
– 9 –
ICX258AL
Image Sensor Characteristics Measurement Method
Measurement conditions
1) In the following measurements, the device drive conditions are at the typical values of the bias and clock
voltage conditions.
2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical
black (OB) level is used as the reference for the signal output, and the value measured at point [
A] in the
drive circuit example is used.
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance: 706cd/m
2
, color temperature of 3200K halogen source) as a subject.
(Pattern for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut
filter and image at F8. The luminous intensity to the sensor receiving surface at this point is defined as the
standard sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Indicate the state which removes an IR cut filter of standard imaging condition
I
.
3) Standard imaging condition
III
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity 1
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/250s, measure the signal output (Vs
1
) at the center of the screen and
substitute the value into the following formula.
60
2. Sensitivity 2
Set to standard imaging condition
II
. After selecting the electronic shutter mode with a shutter speed of
1/1000s, measure the signal output (Vs
2
) at the center of the screen
and substitute the value into the following formula.
60
3. Saturation signal
Set to standard imaging condition
III
. After adjusting the luminous intensity to 10 times the intensity with the
average value of the signal output, 200mV, measure the minimum value of the signal output.
4. Smear
Set to standard imaging condition
III
. With the lens diaphragm at F5.6 to F8, adjust the luminous intensity to
500 times the intensity with average value of the signal output, 200mV. When the readout clock is stopped
and the charge drain is executed by the electronic shutter at the respective H blankings, measure the
maximum value YSm [mV] of the signal output and substitute the value into the following formula.
S1 = Vs
1
×
[mV]
250
S2 = Vs
2
×
[mV]
1000
Sm = 20
×
log
[dB] (1/10V method conversion value)
×
×
500
1
200
VSm
10
1
相關PDF資料
PDF描述
ICX259AK Diagonal 6mm (Type 1/3) CCD Image Sensor for PAL Color Video Cameras
ICX259AL Diagonal 6mm (Type 1/3) CCD Image Sensor for CCIR B/W Video Cameras
ICX262 Timing Generator for Frame Readout CCD Image Sensor
ICX262AQ Diagonal 8.933mm (Type 1/1.8) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras
ICX262AQF Diagonal 8.933mm (Type 1/1.8) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras
相關代理商/技術參數
參數描述
ICX259AK 制造商:Sony Batteries 功能描述:
ICX259AL 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 6mm (Type 1/3) CCD Image Sensor for CCIR B/W Video Cameras
ICX262 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Timing Generator and Signal Processor for Frame Readout CCD Image Sensor
ICX262AQ 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 8.933mm (Type 1/1.8) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras
ICX262AQF 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 8.933mm (Type 1/1.8) Frame Readout CCD Image Sensor with Square Pixel for Color Cameras