- 您現在的位置：買賣IC網 > PDF目錄383095 > ICX085AL (Sony Corporation) Diagonal 11mm (Type 2/3) Progressive Scan CCD Image Sensor With Square Pixel For B/W Cameras(對角線式、11毫米(2/3型)步進掃描CCD圖像傳感器（具有正方形像素，用于黑白照相機）) PDF資料下載
參數資料
| 型號： | ICX085AL |
| 廠商： | Sony Corporation |
| 英文描述： | Diagonal 11mm (Type 2/3) Progressive Scan CCD Image Sensor With Square Pixel For B/W Cameras(對角線式、11毫米(2/3型)步進掃描CCD圖像傳感器（具有正方形像素，用于黑白照相機）) |
| 中文描述： | 對角線11毫米（類型2 / 3）漸進式掃描CCD在廣場為/黑白攝像機（對角線式，11毫米（2 / 3型）步進掃描防治荒漠化圖像傳感器（具有正方形像素，用于黑白照相機像素圖像傳感器）） |
| 文件頁數： | 10/20頁 |
| 文件大?。?/td> | 211K |
| 代理商： | ICX085AL |
– 10 –
ICX085AL
Image Sensor Characteristics Measurement Method
Measurement conditions
1) In the following measurements, the substrate voltage is set to the value indicated on the device, and the
device drive conditions are at the typical values of the bias and clock voltage conditions.
2) In the following measurements, spot blemishes are excluded and, unless otherwise specified, the optical
black level (OB) is used as the reference for the signal output, which is taken as the value measured at point
[
B] of the measurement system.
Definition of standard imaging conditions
1) Standard imaging condition
I
:
Use a pattern box (luminance: 706cd/m
2
, color temperature of 3200K halogen source) as a subject. (Pattern
for evaluation is not applicable.) Use a testing standard lens with CM500S (t = 1.0 mm) as an IR cut filter
and image at F8. The luminous intensity to the sensor receiving surface at this point is defined as the
standard sensitivity testing luminous intensity.
2) Standard imaging condition
II
:
Image a light source (color temperature of 3200K) with a uniformity of brightness within 2% at all angles.
Use a testing standard lens with CM500S (t = 1.0 mm) as an IR cut filter. The luminous intensity is adjusted
to the value indicated in each testing item by the lens diaphragm.
1. Sensitivity
Set to standard imaging condition
I
. After selecting the electronic shutter mode with a shutter speed of
1/80s, measure the signal output (V
S
) at the center of the screen, and substitute the value into the following
formula.
S = V
S
x 80
2. Saturation signal
Set to standard imaging condition
II
. After adjusting the luminous intensity to 10 times the intensity with the
average value of the signal output, 150mV, measure the minimum value of the signal output.
3. Smear
Set to standard imaging condition
II
. With the lens diaphragm at F5.6 to F8, first adjust the luminous
intensity to 500 times the intensity with the average value of the signal output, 150mV. Then after the
readout clock is stopped and the charge drain is executed by the electronic shutter at the respective H
blankings, measure the maximum value (VSm [mV]) of the signal output and substitute the value into the
following formula.
Sm = VSm
150
500
10
12
1
1
相關PDF資料 |
PDF描述 |
|---|---|
| ICX086AKB | Diagonal 4.5mm (Type 1/4) CCD Image Sensor for NTSC Color Video Cameras |
| ICX086AK | 1/4-Inch CCD Image Sensor For NTSC Color Video Cameras(1/4 英寸CCD圖像傳感器（用于NTSC制式彩色攝像機）) |
| ICX086AL | 1/4-Inch CCD Image Sensor For EIA B/W Video Cameras(1/4 英寸CCD圖像傳感器（用于EIA黑白攝像機）) |
| ICX087AKB | Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras |
| ICX087AK | Diagonal 4.5mm (Type 1/4) CCD Image Sensor For PAL Color Video Cameras(對角線式、4.5毫米(1/4型)CCD圖像傳感器（用于PAL制式彩色攝像機）) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICX086AK | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for NTSC Color Video Cameras |
| ICX086AKB | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for NTSC Color Video Cameras |
| ICX086AL | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for EIA B/W Video Cameras |
| ICX087AK | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras |
| ICX087AKB | 制造商:SONY 制造商全稱:Sony Corporation 功能描述:Diagonal 4.5mm (Type 1/4) CCD Image Sensor for PAL Color Video Cameras |
發布緊急采購，3分鐘左右您將得到回復。