- 您現在的位置：買賣IC網 > PDF目錄360786 > ICS952302yGLF-T Frequency Generator for TransmetaTM PDF資料下載
參數資料
| 型號： | ICS952302yGLF-T |
| 英文描述： | Frequency Generator for TransmetaTM |
| 中文描述： | 頻率發生器TransmetaTM |
| 文件頁數： | 11/15頁 |
| 文件大?。?/td> | 128K |
| 代理商： | ICS952302YGLF-T |
11
ICS952302
0957B—10/05/04
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up,
they act as input pins. The logic level (voltage) that is
present on these pins at this time is read and stored into
a 5-bit internal data latch. At the end of Power-On reset,
(see AC characteristics for timing values), the device
changes the mode of operations for these pins to an
output function. In this mode the pins produce the
specified buffered clocks to external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD
(logic 1) power supply or the GND (logic 0) voltage
potential. A 10 Kilohm (10K) resistor is used to provide
both the solid CMOS programming voltage needed during
the power-up programming period and to provide an
insignificant load on the output clock during the subsequent
operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
8.2K
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the
series termination resistor to minimize the current loop
area. It is more important to locate the series termination
resistor close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS952601yGLFT | Programmable Timing Control Hub⑩ for Next Gen P4⑩ processor |
| ICS952601 | 16-Bit Buffers/Drivers With 3-State Outputs 48-TVSOP -40 to 85 |
| ICS952601yFLFT | Programmable Timing Control Hub⑩ for Next Gen P4⑩ processor |
| ICS952606 | Programmable Timing Control Hub for Next Gen P4 processor |
| ICS952606FLFT | Programmable Timing Control Hub for Next Gen P4 processor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS952303AK | 制造商:INT_CIR_SYS 功能描述: |
| ICS952601 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:Programmable Timing Control HubTM for Next Gen P4TM Processor |
| ICS952601EFLF | 功能描述:IC TIMING CTRL HUB P4 56-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:TCH™ 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| ICS952601EFLFT | 功能描述:IC TIMING CTRL HUB P4 56-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:TCH™ 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ICS952601EGLF | 功能描述:IC TIMING CTRL HUB P4 56-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:TCH™ 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6 |
發布緊急采購，3分鐘左右您將得到回復。