- 您現在的位置：買賣IC網 > PDF目錄67708 > ICS951702YGLF-T (INTEGRATED DEVICE TECHNOLOGY INC) 146.66 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 PDF資料下載
參數資料
| 型號： | ICS951702YGLF-T |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 146.66 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| 封裝： | 6.10 MM, 0.50 MM PITCH, MO-153, TSSOP-56 |
| 文件頁數： | 3/12頁 |
| 文件大小： | 159K |
| 代理商： | ICS951702YGLF-T |
11
ICS951702
Advance Information
0664—07/29/02
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) on the ICS9248-
174 serve as dual signal functions to the device. During
initial power-up, they act as input pins. The logic level
(voltage) that is present on these pins at this time is read
and stored into a 5-bit internal data latch. At the end of
Power-On reset, (see AC characteristics for timing values),
the device changes the mode of operations for these pins
to an output function. In this mode the pins produce the
specified buffered clocks to external loads.
To program (load) the internal configuration register for
these pins, a resistor is connected to either the VDD
(logic 1) power supply or the GND (logic 0) voltage
potential. A 10 Kilohm (10K) resistor is used to provide
both the solid CMOS programming voltage needed during
the power-up programming period and to provide an
insignificant load on the output clock during the subsequent
operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
W
8.2K
W
Figure 1 shows a means of implementing this function
when a switch or 2 pin header is used. With no jumper is
installed the pin will be pulled high. With the jumper in
place the pin will be pulled low. If programmability is not
necessary, than only a single resistor is necessary. The
programming resistors should be located close to the
series termination resistor to minimize the current loop
area. It is more important to locate the series termination
resistor close to the driver than the programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS951703YGLF-T | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS951703YF-T | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS951703YFLF-T | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS951703YF-T | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
| ICS951703YGLF-T | 100 MHz, PROC SPECIFIC CLOCK GENERATOR, PDSO56 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS951901 | 制造商:ICS 制造商全稱:ICS 功能描述:Programmable Frequency Generator & Integrated Buffers for Pentium III Processor |
| ICS951901AF | 功能描述:IC FREQ GENERATOR/BUFFER 48-SSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ICS951901AFLF | 功能描述:IC FREQ GENERATOR/BUFFER 48-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ICS951901AFLFT | 功能描述:IC FREQ GENERATOR/BUFFER 48-SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
| ICS951901AFT | 功能描述:IC FREQ GENERATOR/BUFFER 48-SSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:28 系列:- 類型:時鐘/頻率發生器 PLL:是 主要目的:Intel CPU 服務器 輸入:時鐘 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:3:22 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:64-TFSOP （0.240"，6.10mm 寬） 供應商設備封裝:64-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。