- 您現在的位置：買賣IC網 > PDF目錄360782 > ICS9248-126 Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ & K6 PDF資料下載
參數資料
| 型號： | ICS9248-126 |
| 英文描述： | Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ & K6 |
| 中文描述： | 頻率發生器 |
| 文件頁數： | 9/11頁 |
| 文件大?。?/td> | 100K |
| 代理商： | ICS9248-126 |
9
ICS9248-185
Fig. 1
Shared Pin Operation -
Input/Output Pins
The I/O pins designated by (input/output) serve as dual
signal functions to the device. During initial power-up, they
act as input pins. The logic level (voltage) that is present on
these pins at this time is read and stored into a 5-bit internal
data latch. At the end of Power-On reset, (see AC
characteristics for timing values), the device changes the
mode of operations for these pins to an output function. In
this mode the pins produce the specified buffered clocks to
external loads.
To program (load) the internal configuration register for these
pins, a resistor is connected to either the VDD (logic 1) power
supply or the GND (logic 0) voltage potential. A 10 Kilohm
(10K) resistor is used to provide both the solid CMOS
programming voltage needed during the power-up
programming period and to provide an insignificant load on
the output clock during the subsequent operating period.
Via to
VDD
Clock trace to load
Series Term. Res.
Programming
Header
Via to Gnd
Device
Pad
2K
8.2K
Figure 1 shows a means of implementing this function when
a switch or 2 pin header is used. With no jumper is installed
the pin will be pulled high. With the jumper in place the pin
will be pulled low. If programmability is not necessary, than
only a single resistor is necessary. The programming resistors
should be located close to the series termination resistor to
minimize the current loop area. It is more important to locate
the series termination resistor close to the driver than the
programming resistor.
相關PDF資料 |
PDF描述 |
|---|---|
| ICS9248-127 | Frequency Generator & Integrated Buffers for PENTIUM/ProTM |
| ICS9248yF-168-T | AMD - K7⑩ Clock Generator for Mobile System |
| ICS9248-50 | Frequency Timing Generator for Pentium II Systems |
| ICS9248BF-55 | Pentium/Pro/IITM System Clock Chip |
| ICS9248yF-39 | Frequency Generator & Integrated Buffers for PENTIUM/ProTM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS9248-127 | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for PENTIUM/ProTM |
| ICS9248-128 | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers |
| ICS9248-131 | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for Celeron & PII/III⑩ |
| ICS9248-134 | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Timing Generator for PENTIUM II/III Systems |
| ICS9248-135 | 制造商:ICS 制造商全稱:ICS 功能描述:Frequency Generator & Integrated Buffers for Celeron & PII/III⑩& K6 |
發布緊急采購，3分鐘左右您將得到回復。