- 您現在的位置：買賣IC網 > PDF目錄8707 > ICS9179BF-03LF (IDT, Integrated Device Technology Inc)IC CLK BUFFER 1:10 133MHZ 28SSOP PDF資料下載
參數資料
| 型號： | ICS9179BF-03LF |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 6/11頁 |
| 文件大小： | 0K |
| 描述： | IC CLK BUFFER 1:10 133MHZ 28SSOP |
| 標準包裝： | 47 |
| 類型： | 扇出緩沖器（分配） |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:10 |
| 差分 - 輸入:輸出： | 無/無 |
| 輸入： | 時鐘 |
| 輸出： | 時鐘 |
| 頻率 - 最大： | 133MHz |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 28-SSOP |
| 包裝： | 管件 |
| 其它名稱： | 9179BF-03LF |
4
ICS9179-03
0258K 12/15/08
1.
The ICS clock generator is a slave/receiver, I
2C component. It can read back the data stored in the latches for
verification. Read-Back will support Intel PIIX4 "Block-Read" protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I
2C interface, the protocol is set to use only "Block-Writes" from the controller. The
bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any complete
byte has been transferred. The Command code and Byte count shown above must be sent, but the data is ignored
for those two bytes. The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
General I
2C serial interface information
The information in this section assumes familiarity with I
2C programming.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D2
(H)
ICS clock will acknowledge
Controller (host) sends a dummy command code
ICS clock will acknowledge
Controller (host) sends a dummy byte count
ICS clock will acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 5
ICS clock will acknowledge each byte one at a time.
How to Read:
Controller (host) will send start bit.
Controler (host) sends the read address D3
(H)
ICS clock will acknowledge
ICS clock will send the byte count
Controller (host) acknowledges
ICS clock sends first byte (Byte 0) through byte 6
Controller (host) will need to acknowledge each byte
Controller (host) will send a stop bit
Notes:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D2(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Byte 6
ACK
Stop Bit
How to Write:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D3(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Byte 6
ACK
Stop Bit
How to Read:
相關PDF資料 |
PDF描述 |
|---|---|
| ICS8S89834AKILFT | IC CLOCK MUX 2:4 1GHZ 16-VFQFN |
| LTC2612CMS8#TR | IC DAC 14BIT DUAL R-R VOUT 8MSOP |
| CY2SSTV850ZCT | IC PLL BUF/DRIV I2C 1:10 48TSSOP |
| AD5320BRT-500RL7 | IC DAC 12BIT R-R W/BUFF SOT23-6 |
| VE-JNK-MY | CONVERTER MOD DC/DC 40V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS9179BF-03LFT | 功能描述:IC CLK BUFFER 1:10 133MHZ 28SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:- 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
| ICS9179BF-03T | 功能描述:IC CLK BUFFER 1:10 133MHZ 28SSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:- 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
| ICS9179F03 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
| ICS9179F-06 | 制造商:ICS 制造商全稱:ICS 功能描述:Zero Delay Buffers |
| ICS9179F12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Industrial Control IC |
發布緊急采購，3分鐘左右您將得到回復。