參數資料
型號: ICS91719YG-T
元件分類: 時鐘及定時
英文描述: PLL BASED CLOCK DRIVER, 1 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16
封裝: 4.40 MM, 0.65 MM PITCH, MO-153, TSSOP-16
文件頁數: 5/10頁
文件大?。?/td> 69K
代理商: ICS91719YG-T
4
ICS91719
0506C—07/28/03
1.
The ICS clock generator is a slave/receiver, I
2C component. It can read back the data stored in the latches for
verification. Read-Back will support Intel PIIX4 "Block-Read" protocol.
2.
The data transfer rate supported by this clock generator is 100K bits/sec or less (standard mode)
3.
The input is operating at 3.3V logic levels.
4.
The data byte format is 8 bit bytes.
5.
To simplify the clock generator I
2C interface, the protocol is set to use only "Block-Writes" from the controller.
The bytes must be accessed in sequential order from lowest to highest byte with the ability to stop after any
complete byte has been transferred. The Command code and Byte count shown above must be sent, but the
data is ignored for those two bytes. The data is loaded until a Stop sequence is issued.
6.
At power-on, all registers are set to a default condition, as shown.
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D2(H)
ACK
Dummy Command Code
ACK
Dummy Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Byte 6
ACK
Byte 7
ACK
Stop Bit
How to Write:
Controller (Host)
ICS (Slave/Receiver)
Start Bit
Address
D3(H)
ACK
Byte Count
ACK
Byte 0
ACK
Byte 1
ACK
Byte 2
ACK
Byte 3
ACK
Byte 4
ACK
Byte 5
ACK
Byte 6
ACK
Byte 7
Stop Bit
How to Read:
General I
2C serial interface information
The information in this section assumes familiarity with I
2C programming.
For more information, contact ICS for an I
2C programming application note.
How to Write:
Controller (host) sends a start bit.
Controller (host) sends the write address D2 (H)
ICS clock will
acknowledge
Controller (host) sends a dummy command code
ICS clock will
acknowledge
Controller (host) sends a dummy byte count
ICS clock will
acknowledge
Controller (host) starts sending first byte (Byte 0)
through byte 6
ICS clock will
acknowledge each byte one at a
time.
Controller (host) sends a Stop bit
How to Read:
Controller (host) will send start bit.
Controller (host) sends the read address D3 (H)
ICS clock will
acknowledge
ICS clock will send the
byte count
Controller (host) acknowledges
ICS clock sends first byte
(Byte 0) through byte 7
Controller (host) will need to acknowledge each
byte
Controller (host) will send a stop bit
Notes:
相關PDF資料
PDF描述
ICS91719YG-T PLL BASED CLOCK DRIVER, 1 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO16
ICS9177-01CF52LF 75 MHz, PROC SPECIFIC CLOCK GENERATOR, PQFP52
ICS9179G-03 LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28
ICS9179G-03-T LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28
ICS9179F-03-LF LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28
相關代理商/技術參數
參數描述
ICS91720 制造商:ICS 制造商全稱:ICS 功能描述:Low EMI, Spread Modulating, Clock Generator
ICS91720BGLF 功能描述:IC CLK GENERATOR LOW EMI 8-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器,PLL,頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS,LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP(7x7) 包裝:帶卷 (TR)
ICS91720BGLFT 功能描述:IC CLK GENERATOR LOW EMI 8-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器,PLL,頻率合成器 系列:- 標準包裝:2,000 系列:- 類型:PLL 時鐘發生器 PLL:帶旁路 輸入:LVCMOS,LVPECL 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:2:11 差分 - 輸入:輸出:是/無 頻率 - 最大:240MHz 除法器/乘法器:是/無 電源電壓:3.135 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:32-LQFP 供應商設備封裝:32-TQFP(7x7) 包裝:帶卷 (TR)
ICS91730 制造商:ICS 制造商全稱:ICS 功能描述:Low EMI, Spread Modulating, Clock Generator
ICS9173-01 制造商:ICS 制造商全稱:ICS 功能描述:Video Genlock PLL