- 您現在的位置：買賣IC網 > PDF目錄8705 > ICS85356AGILFT (IDT, Integrated Device Technology Inc)IC CLOCK MUX 2:1 900MHZ 20-TSSOP PDF資料下載
參數資料
| 型號： | ICS85356AGILFT |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 12/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CLOCK MUX 2:1 900MHZ 20-TSSOP |
| 標準包裝： | 2,500 |
| 系列： | HiPerClockS™ |
| 類型： | 多路復用器 |
| 電路數： | 2 |
| 比率 - 輸入:輸出： | 2:1 |
| 差分 - 輸入:輸出： | 是/是 |
| 輸入： | HCSL，LVDS，LVHSTL，LVPECL，SSTL |
| 輸出： | LVPECL |
| 頻率 - 最大： | 900MHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-TSSOP（0.173"，4.40mm 寬） |
| 供應商設備封裝： | 20-TSSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 85356AGILFT |
ICS85356AMI REVISION B MAY 10, 2010
6
2010 Integrated Device Technology, Inc.
ICS85356I Data Sheet
2:1, DIFFERENTIAL-TO-3.3V LVPECL/ECL CLOCK MULTIPLEXER
Application Information
Wiring the Differential Input to Accept Single-Ended Levels
Figure 1 shows how a differential input can be wired to accept single
ended levels. The reference voltage VREF = VCC/2 is generated by
the bias resistors R1 and R2. The bypass capacitor (C1) is used to
help filter noise on the DC bias. This bias circuit should be located as
close to the input pin as possible. The ratio of R1 and R2 might need
to be adjusted to position the VREF in the center of the input voltage
swing. For example, if the input clock swing is 2.5V and VCC = 3.3V,
R1 and R2 value should be adjusted to set VREF at 1.25V. The values
below are for when both the single ended swing and VCC are at the
same voltage. This configuration requires that the sum of the output
impedance of the driver (Ro) and the series resistance (Rs) equals
the transmission line impedance. In addition, matched termination at
the input will attenuate the signal in half. This can be done in one of
two ways. First, R3 and R4 in parallel should equal the transmission
line impedance. For most 50
applications, R3 and R4 can be 100.
The values of the resistors can be increased to reduce the loading for
slower and weaker LVCMOS driver. When using single-ended
signaling, the noise rejection benefits of differential signaling are
reduced. Even though the differential input can handle full rail
LVCMOS signaling, it is recommended that the amplitude be
reduced. The datasheet specifies a lower differential amplitude,
however this only applies to differential signals. For single-ended
applications, the swing can be larger, however VIL cannot be less
than -0.3V and VIH cannot be more than VCC + 0.3V. Though some
of the recommended components might not be used, the pads
should be placed in the layout. They can be utilized for debugging
purposes. The datasheet specifications are characterized and
guaranteed by using a differential signal.
Figure 1. Recommended Schematic for Wiring a Differential Input to Accept Single-ended Levels
Recommendations for Unused Input and Output Pins
Inputs:
CLK/nCLK Inputs
For applications not requiring the use of the differential input, both
CLK and nCLK can be left floating. Though not required, but for
additional protection, a 1k
resistor can be tied from CLK to ground.
Control Pins
All control pins have internal pull-ups or pull-downs; additional
resistance is not required but can be added for additional protection.
A 1k
resistor can be used.
Inputs:
LVPECL Outputs
All unused LVPECL outputs can be left floating. We recommend that
there is no trace attached. Both sides of the differential output pair
should either be left floating or terminated.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-JNF-MY | CONVERTER MOD DC/DC 72V 50W |
| V150A3V3H264BL2 | CONVERTER MOD DC/DC 3.3V 264W |
| VI-JND-MY | CONVERTER MOD DC/DC 85V 50W |
| V150A5H400BG3 | CONVERTER MOD DC/DC 5V 400W |
| VI-JNB-MY | CONVERTER MOD DC/DC 95V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS85356AMILF | 功能描述:IC CLOCK MUX 2:1 900MHZ 20-SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:HiPerClockS™ 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
| ICS85356AMILFT | 功能描述:IC CLOCK MUX 2:1 900MHZ 20-SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:HiPerClockS™ 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
| ICS85357AG-01LF | 功能描述:IC CLOCK MUX 4:1/2:1 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:HiPerClockS™ 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
| ICS85357AG-01LFT | 功能描述:IC CLOCK MUX 4:1/2:1 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:HiPerClockS™ 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
| ICS85357AG-11LF | 功能描述:IC CLOCK MUX 4:1/2:1 20-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:HiPerClockS™ 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。