- 您現在的位置：買賣IC網 > PDF目錄9982 > ICS1893BKLF (IDT, Integrated Device Technology Inc)PHYCEIVER LOW PWR 3.3V 56-VQFN PDF資料下載
參數資料
| 型號： | ICS1893BKLF |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 73/133頁 |
| 文件大?。?/td> | 0K |
| 描述： | PHYCEIVER LOW PWR 3.3V 56-VQFN |
| 標準包裝： | 260 |
| 系列： | PHYceiver™ |
| 類型： | PHY 收發器 |
| 規程： | MII |
| 電源電壓： | 3.14 V ~ 3.47 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 56-VFQFP-EP（8x8） |
| 包裝： | 管件 |
| 其它名稱： | 1893BKLF 800-1019 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁當前第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁
ICS1893BF, Rev. F, 5/13/10
May, 2010
44
Chapter 6 Functional Blocks
ICS1893BF Data Sheet - Release
Copyright 2009, IDT, Inc.
All rights reserved.
6.5.7 10Base-T Operation: Carrier Detection
The ICS1893BF has a 10Base-T Carrier Detection Function that establishes the state of its Carrier Sense
signal (CRS), based upon the state of its Transmit and Receive state machines. These functions indicate
whether the ICS1893BF is (1) transmitting data, (2) receiving data, or (3) in a collision state (that is, the
ICS1893BF is both transmitting and receiving data on its twisted-pair medium, as defined in the ISO/IEC
8802-3 standard). When the ICS1893BF is configured for:
Half-duplex operations, the ICS1893BF asserts its CRS signal when either transmitting or receiving data.
Full-duplex operations, the ICS1893BF asserts its CRS signal only when it is receiving data.
6.5.8 10Base-T Operation: Collision Detection
The ICS1893BF has a 10Base-T Collision Detection Function that establishes the state of its Collision
Detection signal (COL) based upon both (1) the state of its Receiver state machine and (2) the state of its
Transmit state machine. When the ICS1893BF is operating in:
Half-duplex mode, the ICS1893BF asserts its COL signal to indicate it is receiving data while
transmission of data is also in progress.
Full-duplex mode, the ICS1893BF always sets its COL signal to FALSE.
6.5.9 10Base-T Operation: Jabber
The ICS1893BF has an ISO/IEC compliant Jabber Detection Function that, when enabled, monitors the
data stream sent to its Twisted-Pair Transmitter to ensure that it does not exceed the 10Base-T Jabber
activation time limit (that is, the maximum transmission time). For more information, see Section 9.5.18,
When the Jabber Detection Function detects that its transmission time exceeds the maximum Jabber
activation time limit and Jabber Detection is enabled, the ICS1893BF asserts its Collision Detect (COL)
signal. During this ISO/IEC specified ‘jabber de-activation time’, the ICS1893BF transmit data stream is
interrupted and prevented from reaching its Twisted-Pair Transmitter. During this time, when interrupting
the data stream and asserting its COL signal, the ICS1893BF transmits Normal Link Pulses and sets its
QuickPoll Detailed Status Register’s Jabber Detected bit (bit 17.2) to logic one. This bit is a latching high
(LH) bit. (For more information on latching high and latching low bits, see Section 7.1.4.1, “Latching High
The ICS1893BF provides an STA with the ability to disable the Jabber Detection Function using the Jabber
Inhibit bit (bit 18.5 in the 10Base-T Operations Register). Setting bit 18.5 to logic:
Zero (the default) enables the Jabber Detection Function.
One disables the Jabber Detection Function.
6.5.10 10Base-T Operation: SQE Test
The ICS1893BF has an ISO/IEC compliant Signal Quality Error (SQE) Test Function used exclusively for
10Base-T operations. When enabled, the ICS1893BF performs the SQE Test at the completion of each
transmitted packet (that is, whenever its TX_EN signal transitions from asserted to de-asserted). When the
ICS1893BF executes its SQE Test, it asserts the COL signal to its MAC Interface for a pre-determined time
duration (ISO/IEC specified). [For more information, see Section 9.5.17, “10Base-T: Heartbeat Timing
相關PDF資料 |
PDF描述 |
|---|---|
| VE-26V-IX-B1 | CONVERTER MOD DC/DC 5.8V 75W |
| VI-B6Y-MY | CONVERTER MOD DC/DC 3.3V 33W |
| VE-26T-IX-B1 | CONVERTER MOD DC/DC 6.5V 75W |
| IDT72261LA20PFI | IC FIFO 8192X18 LP 20NS 64QFP |
| ICS1894K-32LF | PHYCEIVER LOW PWR 3.3V 32QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS1893BKLFT | 功能描述:PHYCEIVER LOW PWR 3.3V 56-VQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| ICS1893BKT | 功能描述:PHYCEIVER LOW PWR 3.3V 56-VQFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| ICS1893BRIEF | 制造商:ICS 制造商全稱:ICS 功能描述:3.3-V 10Base-T/100Base-TX Integrated PHYceiver |
| ICS1893BY-10 | 功能描述:PHYCEIVER LOW PWR 3.3V 64-TQFP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ICS1893BY-10LF | 功能描述:PHYCEIVER LOW PWR 3.3V 64-TQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:PHYceiver™ 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。