- 您現在的位置：買賣IC網 > PDF目錄5528 > ICL7622DCPD+ (Maxim Integrated Products)IC OPAMP DUAL LP CMOS 14-DIP PDF資料下載
參數資料
| 型號： | ICL7622DCPD+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/26頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP DUAL LP CMOS 14-DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 25 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 0.16 V/µs |
| 增益帶寬積： | 480kHz |
| 電流 - 輸入偏壓： | 1pA |
| 電壓 - 輸入偏移： | 5000µV |
| 電流 - 電源： | 100µA |
| 電壓 - 電源，單路/雙路(±)： | 2 V ~ 16 V，±1 V ~ 8 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 14-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 14-PDIP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1385 (CN2011-ZH PDF) |
ICL761X–ICL764X
Single/Dual/Triple/Quad
Operational Amplifiers
______________________________________________________________________________________
21
Detailed Description
Quiescent Current Selection
The voltage input to the IQ pin of the single and triple
amplifiers selects a quiescent current (IQ) of 10A,
100A, or 1000A. The dual and quad amplifiers have
fixed quiescent current (IQ) settings. Unity-gain band-
width and slew-rate increase with increasing quiescent
current, as does output sink current capability. The out-
put source current capability is independent of quies-
cent current.
The lowest IQ setting that results in sufficient bandwidth
and slew rate should be selected for each specific
application.
The IQ pin of the single and triple amplifiers controls
the quiescent current as follows:
Input Offset Nulling
The input offset can be nulled by connecting a 25k
pot between the OFFSET terminals with the wiper con-
nected to V+. At quiescent currents of 1mA and 100A,
the nulling range provided is adequate for all VOS
selections. However, with higher values of VOS, and an
IQ of 10A, nulling may not be possible.
Frequency Compensation
All of the ICL7611 and ICL7621 series except the
ICL7614 are internally compensated for unity-gain
operation. The ICL7614 is externally compensated by a
capacitor connected between COMP and OUT pins,
with 39pF being greater than unity. The compensation
capacitor value may be reduced to increase the band-
width and slew rate. The ICL7132 is not compensated
and does not have frequency compensation pins. Use
only at gains 20 at IQ of 1mA; at gains > 10 at IQ of
100A; at gain > 5 at IQ of 10A.
Output Loading Considerations
Approximately 70% of the amplifier’s quiescent current
flows in the output stage. The output swing can
approach the supply rails for output loads of 1M
,
100k
, and 10k, using the output stage in a highly
linear Class A mode. Crossover distortion is avoided
and the voltage gain is maximized in this mode. The
output stage, however, can also be operated in Class
AB, which supplies higher output currents (see the
Typical Operating Characteristics). The voltage gain
decreases and the output transfer characteristic is non-
linear during the transition from Class A to Class B
operation.
The output stage, with a gain that is directly proportion-
al to load impedance, approximates a transconduc-
tance amplifier. Approximately the same open-loop
gains are obtained at each of the IQ settings if corre-
sponding loads of 10k
, 100k, and 1M are used.
The maximum output source current is higher than the
maximum sink current, and is independent of IQ.
Like most amplifiers, there are output loads for which
the amplifier stability is not guaranteed. In particular,
avoid capacitive loads greater than 100pF; and while
on the 1mA IQ setting, avoid loads less than 5k. Since
the output stage is a transconductance output, very
large (>10F) capacitive loads will create a dominant
pole and the output will be stable, even with loads that
are less than 5k
.
Extended Common-Mode Voltage Range
(ICL7612/ICL7616)
A common-mode voltage range that includes both V+
and V- is often desirable, especially in single-supply
operation. The ICL7612/ICL7616 extended common-
mode range op amps are designed specifically to meet
this need. The ICL7612 input common-mode voltage
range (CMVR) extends beyond both power-supply rails
when operated with at least 3V total supply and an IQ
of 10A or 100A. The ICL7616 CMVR includes the
negative supply voltage (or ground when operated with
a single supply) at an IQ or 10A or 100A.
PC Board Layout
Careful PC board layout techniques must be used to
take full advantage of the very low bias current of the
ICL7611 family. The inputs should be encircled with a
low-impedance trace, or guard, that is at the same
potential as the inputs. In an inverting amplifier, this is
normally ground; in a unity-gain buffer connect the
guard to the output. A convenient way of guarding the
8-pin TO-99 version of the ICL7611 is to use a 10-pin
circle, with the two extra pads on either side of the
input pins to provide space for a guard ring (see Figure
8). Assembled boards should be carefully cleaned,
and if a high humidity environment is expected, confor-
mally coated.
IQ = 10A
IQ pin to V+
IQ = 100A
IQ pin between V- + 0.8V and V+ - 0.8V
IQ = 1mA
IQ pin to V-
相關PDF資料 |
PDF描述 |
|---|---|
| TR2/C515-3-R | FUSE 250V 3A T-LAG AXL T/R |
| P6KE24HE3/54 | TVS 600W 24V 10% UNIDIR AXIAL |
| 536507-7 | CONN 2MM FB RCPT 144POS R/A GOLD |
| P6KE24CHE3/54 | TVS 600W 24V 10% BIDIR AXIAL |
| ICL7622DCPD | IC OPAMP DUAL LP CMOS 14-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL7622DCPD+ | 功能描述:運算放大器 - 運放 Dual CMOS Low Power RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| ICL7622DCPE | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Triple/Quad Operational Amplifiers |
| ICL7622DCSA | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Triple/Quad Operational Amplifiers |
| ICL7622DCSD | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| ICL7622DCSE | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single/Dual/Triple/Quad Operational Amplifiers |
發布緊急采購，3分鐘左右您將得到回復。