- 您現在的位置：買賣IC網 > PDF目錄383083 > ICL7104-16 (Intersil Corporation) 16-Bit, Microprocessor-Compatible, 2-Chip, A/D Converter(16位、微處理器兼容的2片ADC) PDF資料下載
參數資料
| 型號： | ICL7104-16 |
| 廠商： | Intersil Corporation |
| 英文描述： | 16-Bit, Microprocessor-Compatible, 2-Chip, A/D Converter(16位、微處理器兼容的2片ADC) |
| 中文描述： | 16位微處理器兼容，2芯片，A / D轉換（16位，微處理器兼容的2片ADC）的 |
| 文件頁數： | 19/21頁 |
| 文件大?。?/td> | 198K |
| 代理商： | ICL7104-16 |
5-24
Initial Clear Circuitry
The internal logic of the 7104 is supplied by an internal
regulator between V++ and Digital Ground. The regulator
includes a low-voltage detector that will clear various
registers. This is intended to ensure that on initial power-up,
the control logic comes up in Auto-Zero, with the 2nd, 3rd,
and 4th MSB bits cleared, and the “mode” F/F cleared (i.e.,
in “direct” mode). This, however, will also clear these regis-
ters if the supply voltage “glitches” to a low enough value.
Additionally, if the supply voltage comes up too fast, this
clear pulse may be too narrow for reliable clearing. In gen-
eral, this is not a problem, but if the UART internal “MODE”
F/F should come up set, the byte and chip ENABLE lines will
become active outputs. In many systems this could lead to
bus conflicts, especially in non-handshake systems. In any
case, SEN should be high (held high for non-handshake sys-
tems) to ensure that the MODE F/F will be cleared as fast as
possible (see Figure 11 for timing). For these and other
reasons, adequate supply bypass is recommended.
Oscillator
The ICL7104-14 is provided with a versatile three terminal
oscillator to generate the internal clock. The oscillator may
be overdriven, or may be operated as an RC or crystal
oscillator.
Figure 14 shows the oscillator configured for RC operation.
The internal clock will be of the same frequency and phase
as the voltage on the CLOCK 3 pin. The resistor and
capacitor should be connected as shown. The circuit will
oscillate at a frequency given by f = 0.45/RC. A 50 - 100k
resistor is recommended for useful ranges of frequency. For
optimum 60Hz line rejection, the capacitor value should be
chosen such that 32768 (-16), 8192 (-14) clock periods is
close to an integral multiple of the 60Hz period.
As a result of pin count limitations, the ICL7104-16 has only
CLOCK 1 and CLOCK 2 available, and cannot be used as
an RC oscillator. The internal clock will correspond to the
inverse of the signal on CLOCK 2. Figure 15 shows a crystal
oscillator circuit, which can be used with both 7104 versions.
If an external clock is to be used, it should be applied to
CLOCK 1. This internal clock will correspond to the signal
applied to this pin.
FIGURE 13. HANDSHAKE TRIGGERED BY MODE
DATA VALID
INTERNAL
CLOCK
INTERNAL
LATCH
STATUS
OUTPUT
MODE
INPUT
INTERNAL
MODE
SEN INPUT
CE/LOAD
AS OUTPUT
UART
NORM
HIGH BYTE
MIDDLE
BYTE DATA
LOW BYTE
HBEN
MBEN
LBEN
ZERO-CROSSING DETECTED
ZERO-CROSSING OCCURS
DATA
DATA
DATA VALID
DATA VALID
STATUS OUTPUT UNAFFECTED
BY UART MODE
LATCH PULSE INHIBITED
IN UART MODE
THREE-STATE WITH PULLUP
THREE-STATE HIGH IMPEDANCE
DON’T CARE
POSITIVE TRANSITION
CAUSES ENTRY INTO
UART MODE
DEINT PHASE III
NOTE: Clock 3 has the same output drive as the bit outputs.
FIGURE 14. RC OSCILLATOR (ICL7104-14 ONLY)
CLOCK
25
26
R
C
2
CLOCK
3
CLOCK
1
24
f
OSC
= 0.45/RC
FIGURE 15. CRYSTAL OSCILLATOR
CLOCK
25
26
2
CLOCK
1
V+
CAPACITOR VALUE
DEPENDS ON CRYSTAL
TYP 0-30pF
CRYSTAL
ICL8052/ICL7104, ICL8068/ICL7104
相關PDF資料 |
PDF描述 |
|---|---|
| ICL7104 | 14-Bit/16-Bit, Microprocessor- Compatible, 2-Chip, A/D Converter |
| ICL7104-14CPL | 14-Bit/16-Bit, Microprocessor- Compatible, 2-Chip, A/D Converter |
| ICL7104-16CPL | 14-Bit/16-Bit, Microprocessor- Compatible, 2-Chip, A/D Converter |
| ICL7106 | 3 1/2 Digital ADC(3 1/2位數，具有直接液晶顯示驅動器的ADC) |
| ICL7107 | 3 1/2 Digital ADC(3 1/2位數，具有直接液晶顯示驅動器的ADC) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICL7104-16CDL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Data Acquisition |
| ICL7104-16CJL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Data Acquisition |
| ICL7104-16CPL | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Precision 4 1/2 Digit, A/D Converter |
| ICL7106 | 制造商:ESTEK 制造商全稱:ESTEK 功能描述:True Differential input and Reference, Direct Display |
| ICL7106_0512 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:3 Digit, LCD/LED Display, A/D Converters |
發布緊急采購，3分鐘左右您將得到回復。