- 您現在的位置：買賣IC網 > PDF目錄360718 > IC42S32400L-6BIG 1M x 32 Bit x 4 Banks (128-MBIT) SDRAM PDF資料下載
參數資料
| 型號： | IC42S32400L-6BIG |
| 英文描述： | 1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
| 中文描述： | 100萬× 32位× 4個銀行（128兆）內存 |
| 文件頁數： | 4/62頁 |
| 文件大?。?/td> | 899K |
| 代理商： | IC42S32400L-6BIG |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁
IC42S32400
IC42S32400L
4
Integrated Circuit Solution Inc.
DR038-0C 02/01/2005
PIN DESCRIPTIONS
Table 1.Pin Details of IC42S32400 and IC42S32400L
Symbol
Type
Description
CLK
Input
Clock:
CLK is driven by the system clock.All SDRAM input signals are sampled on the positive edge
of CLK.CLK also increments the internal burst counter and controls the output registers.
CKE
Input
Clock Enable:
CKE activates(HIGH)and deactivates(LOW)the CLK signal.If CKE goes low syn-
chronously with clock(set-up and hold time same as other inputs),the internal clock is suspended
from the next clock cycle and the state of output and burst address is frozen as long as the CKE
remains low.When all banks are in the idle state,deactivating the clock controls the entry to the
Power Down and Self Refresh modes.CKE is synchronous except after the device enters Power
Down and Self Refresh modes,where CKE becomes asynchronous until exiting the same mode.
The input buffers,including CLK,are disabled during Power Down and Self Refresh modes,providing
low standby power.
Bank Select:
BS0 and BS1 defines to which bank the BankActivate,Read,Write,or BankPrecharge
command is being applied.
Address Inputs:
A0-A11 are sampled during the BankActivate command (row address A0-A11)and
Read/Write command (column address A0-A7 with A10 defining Auto Precharge) to select one
location in the respective bank.During a Precharge command,A10 is sampled to determine if all
banks are to be precharged (A10 =HIGH).
BS0,BS1
Input
A0-A11
Input
The address inputs also provide the op-code during a Mode Register Set .
CS#
Input
Chip Select:
CS#enables (sampled LOW)and disables (sampled HIGH)the command decoder.All
commands are masked when CS#is sampled HIGH.CS#provides for external bank selection on
systems with multiple banks.It is considered part of the command code.
RAS#
Input
Row Address Strobe:
The RAS#signal defines the operation commands in conjunction with the
CAS#and WE#signals and is latched at the positive edges of CLK.When RAS# and CS#are as-
serted “LOW”and CAS#is asserted “HIGH,”either the BankActivate command or the Precharge
command is selected by the WE#signal.When the WE#is asserted “HIGH,”the BankActivate com-
mand is selected and the bank designated by BS is turned on to the active state.When the WE#is
asserted “LOW,”the Precharge command is selected and the bank designated by BS is switched to
the idle state after the precharge operation.
CAS#
Input
Column Address Strobe:
The CAS#signal defines the operation commands in conjunction with the
RAS#and WE#signals and is latched at the positive edges of CLK. When RAS#is held “HIGH”and
CS#is asserted “LOW,”the column access is started by asserting CAS#”LOW.”Then,the Read or
Write command is selected by asserting WE# “LOW”or “HIGH.”
WE#
Input
Write Enable:
The WE#signal defines the operation commands in conjunction with the RAS#and
CAS#signals and is latched at the positive edges of CLK.The WE#input is used to select the
BankActivate or Precharge command and Read or Write command.
DQM0-3 Input
Data Input/Output Mask:
DQM0-DQM3 are byte specific,nonpersistent I/O buffer controls. The I/O
buffers are placed in a high-z state when DQM is sampled HIGH.Input data is masked when DQM
is sampled HIGH during a write cycle.Output data is masked (two-clock latency)when DQM is
sampled HIGH during a read cycle.DQM3 masks DQ31-DQ24,DQM2 masks DQ23-DQ16,DQM1
masks DQ15-DQ8,and DQM0 masks DQ7-DQ0.
DQ0-31 Input/Output
Data I/O:
The DQ0-31 input and output data are synchronized with the positive edges of
CLK.The I/Os are byte-maskable during Reads and Writes.
相關PDF資料 |
PDF描述 |
|---|---|
| IC42S32400L-6T | 1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
| IC42S32400L-6TG | CABLE ASSEMBLY; LEAD-FREE SOLDER; 7/16" MALE TO N MALE; 50 OHM, RG393/U COAX |
| IC42S32400L-6TI | 1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
| IC42S32400L-6TIG | 1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
| IC42S32400L-7B | 1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IC42S32400L-6T | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
| IC42S32400L-6TG | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
| IC42S32400L-6TI | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
| IC42S32400L-6TIG | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
| IC42S32400L-7B | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 32 Bit x 4 Banks (128-MBIT) SDRAM |
發布緊急采購，3分鐘左右您將得到回復。