- 您現在的位置：買賣IC網 > PDF目錄360716 > IC42S16400-7TIG 1M x 16Bit x 4 Banks (64-MBIT) SDRAM PDF資料下載
參數資料
| 型號： | IC42S16400-7TIG |
| 英文描述： | 1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
| 中文描述： | 100萬× 16 × 4銀行（64兆位）內存 |
| 文件頁數： | 20/68頁 |
| 文件大?。?/td> | 1092K |
| 代理商： | IC42S16400-7TIG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
IC42S16400
20
Integrated Circuit Solution Inc.
DR034-0E 12/02/2003
Auto Precharge
During a read or write command cycle, A10 controls whether auto precharge is selected. If A10 is high in the read or write
command (Read with Auto precharge command or Write with Auto precharge command), auto precharge is selected and
begins automatically.
In the write cycle, t
DAL
(min.) must be satisfied before asserting the next activate command to the bank being precharged.
When using auto precharge in the read cycle, knowing when the precharge starts is important because the next activate
command to the bank being precharged cannot be executed until the precharge cycle ends. Once auto precharge has
started, an activate command to the bank can be asserted after t
RP
has been satisfied.
A Read or Write command without auto - precharge can be terminated in the midst of a burst operation. However, a Read
or Write command with auto - precharge can not be interrupted by the same bank commands before the entire burst opera-
tion is completed. Therefore use of the same bank Read, Write, Precharge or Burst Stop command is prohibited during a
read or write cycle with auto - precharge. It should be noted that the device will not respond to the Auto - Precharge com-
mand if the device is programmed for full page burst read or write cycles.
The timing when the auto precharge cycle begins depends both on both the
CAS
Iatency programmed into the mode reg-
ister and whether the cycle is read or write.
Read with Auto Precharge
During a READA cycle, the auto precharge begins one clock earlier (CL = 2) or two clocks earlier (CL = 3) than the last word
output.
READ with AUTO PRECHARGE
Burst lengh = 4
CLK
Command
CAS latency = 2
DQ
Command
CAS latency = 3
DQ
Remark READA means READ with AUTO PRECHARGE
Hi - Z
Auto precharge starts
QB0
QB3
QB2
QB1
READA B
READA B
T0
T1
T2
T3
T4
T5
T6
T7
Auto precharge starts
Hi - Z
T8
QB0
QB3
QB2
QB1
No New Command to Bank B
No New Command to Bank B
相關PDF資料 |
PDF描述 |
|---|---|
| IC42S16400 | 1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
| IC42S16400-6BG | RES 100-OHM 5% 0.1W 200PPM THICK-FILM SMD-0603 5K/REEL-7IN-PA |
| IC42S16400-6BIG | 1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
| IC42S16400-6T | 1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
| IC42S16400-6TG | RES 1K-OHM 1% 0.1W 100PPM THICK-FILM SMD-0603 5K/REEL-7IN-PA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IC42S16400A | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
| IC42S16400A-6BG | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
| IC42S16400A-6BIG | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
| IC42S16400A-6T | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
| IC42S16400A-6TG | 制造商:ICSI 制造商全稱:Integrated Circuit Solution Inc 功能描述:1M x 16Bit x 4 Banks (64-MBIT) SDRAM |
發布緊急采購，3分鐘左右您將得到回復。