參數資料
型號： IBM25PPC750L-GB300C2SR
英文描述： Microprocessor
中文描述： 微處理器
文件頁數： 45/50頁
文件大?。?/td> 516K
代理商： IBM25PPC750L-GB300C2SR
5/20/99
Version 1.51
PowerPC 740 and PowerPC 750 Datasheet
Page 41
PowerPC 740 and PowerPC 750 Embedded Microprocessor
IBM CMOS 0.20 um Copper Technology EMPPC740L and EMPPC750L
Heat generated on the active side (ball) of the chip is conducted through the silicon, then through the heat
sink attach material (or thermal interface material), and finally to the heat sink; where it is removed by forced-
air convection. Since the silicon thermal resistance is quite small, for a first-order analysis, the temperature
drop in the silicon may be neglected. Thus, the heat sink attach material and the heat sink conduction/con-
vective thermal resistances are the dominant terms.
Adhesives and Thermal Interface Materials
A thermal interface material is recommended at the package lid-to-heat sink interface to minimize the thermal
contact resistance. For those applications where the heat sink is attached by a spring clip mechanism,
Figure 22 shows the thermal performance of three thin-sheet thermal-interface materials (silicon, graphite/oil,
flouroether oil), a bare joint, and a joint with thermal grease, as a function of contact pressure. As shown, the
performance of these thermal interface materials improves with increasing contact pressure. The use of ther-
mal grease significantly reduces the interface thermal resistance. That is, the bare joint results in a thermal
resistance approximately 7 times greater than the thermal grease joint.
Heat sinks are attached to the package by means of a spring clip to holes in the printed-circuit board (see
Figure 20). Therefore the synthetic grease offers the best thermal performance, considering the low interface
pressure. Of course, the selection of any thermal interface material depends on many factors – thermal per-
formance requirements, manufacturability, service temperature, dielectric properties, cost, etc.
Figure 21. C4 Package with Heat Sink Mounted to a Printed-Circuit Board
External Resistance
External Resistance
Internal Resistance
(Note the internal versus external package resistance.)
Radiation
Convection
Radiation
Convection
Heat Sink
Die/Package
Chip Junction
Printed-Circuit Board
Thermal Interface Material
Package/Leads
Powered by ICminer.com Electronic-Library Service CopyRight 2003
相關PDF資料
PDF描述
IBM25PPC750L-GB300C2ST Microprocessor
IBM25PPC750L-GB300C2T Microprocessor
IBM25PPC750L-GB300D2R Microprocessor
IBM25PPC750L-GB300D2SR Microprocessor
IBM25PPC750L-GB300D2ST Microprocessor
相關代理商/技術參數
參數描述
IBM25PPC750L-GB300C2ST 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
IBM25PPC750L-GB300C2T 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
IBM25PPC750L-GB300D2R 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
IBM25PPC750L-GB300D2SR 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
IBM25PPC750L-GB300D2ST 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microprocessor
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*