參數資料
型號： IBM25PPC750GXEBB6542T
元件分類： 微控制器/微處理器
英文描述： 32-BIT, 1000 MHz, RISC PROCESSOR, CBGA292
封裝： 21 X 21 MM, 1 MM PITCH, CERAMIC, BGA-292
文件頁數： 68/74頁
文件大?。?/td> 1054K
代理商： IBM25PPC750GXEBB6542T
Datasheet
IBM PowerPC 750GX RISC Microprocessor
DD1.X
System Design Information
Page 70 of 73
750GX_ds_body.fm SA14-2765-02
September 2, 2005
5.9.3 I/O Voltage Mode Selection
Selection between 1.8 V, 2.5 V, or 3.3 V I/O modes is accomplished by using the BVSEL and L1_TSTCLK
pins:
If BVSEL = 1 and L1_TSTCLK = 0, then the 3.3 V mode is enabled.
If BVSEL = 1 and L1_TSTCLK = 1, then the 2.5 V mode is enabled.
If BVSEL = 0 and L1_TSTCLK = 1, then the 1.8 V mode is enabled.
Note: Do not set BVSEL = 0 and L1_TSTCLK = 0 since it yields an invalid mode.
5.9.4 QACK Signal Implementation for Selected Features
5.9.4.1 Precharge Duration Selection and Application
An extended precharge feature is available for the signals ABB, DBB, and ARTRY in situations where the
loading and net topology of these signals requires a longer precharge duration for the signals to attain a valid
level.
This feature has not been fully tested and should not be necessary in a properly designed system, even at
200 MHz. System designers should assume standard precharge as the default selection, with an option to
use extended precharge.
The bus signals, ABB, DBB, and ARTRY, require a precharge to the inactive state (bus high) before going to
tristate. The precharge duration in standard precharge mode is approximately one half cycle, and should be
used for systems with point-to-point topologies. Extended precharge mode increases the precharge duration
to one cycle. This increase may be required for bus speeds approaching 200 MHz when bus loading is high.
QACK in a logical high state at the transition of HRESET from asserted to negated enables standard pre-
charge mode in the 750GX. QACK in a logical low state at the transition of HRESET from asserted to negated
enables extended pre-charge mode in the 750GX.
Table 5-10. Summary of Mode Select
Mode
750GX
32-bit mode
Sample TLBISYNC to select
High = 64-bit mode
Low = 32-bit mode
Data retry mode
Selects DRTRY mode.
0 at HRESET transition
No DRTRY mode
1 at HRESET transition
DRTRY mode
Factory usage modes
Factory usage modes are selected by sensing the data bus disable (DBDIS),
data bus write-only (DBWO), and L2_TSTCLK pins at the transition of
HRESET from low to high. These pins should be held inactive (high) at the
HRESET transition for normal machine operation.
I/O mode selection
3.3 V
±165 mV (BVSEL = 1, L1_TSTCLK = 0) or
2.5 V
±125 mV (BVSEL = 1, L1_TSTCLK = 1) or
1.8 V
±100 mV (BVSEL = 0, L1_TSTCLK = 1)
Standard/extended precharge mode
QACK in a logical high state at the transition of HRESET from asserted to
negated enables standard precharge mode, the recommended default. See
Section 5.9.4.1 for details.
相關PDF資料
PDF描述
IBM25PPC750GXEAB5042T 32-BIT, 933 MHz, RISC PROCESSOR, CBGA292
IBM25PPC750GXEAB6542T 32-BIT, 1000 MHz, RISC PROCESSOR, CBGA292
IBM25PPC750GXEAB1033T 32-BIT, 733 MHz, RISC PROCESSOR, CBGA292
IBM25PPC750L-EB0C375W 32-BIT, 375 MHz, RISC PROCESSOR, CBGA360
IBM25PPC750L-FB0B333W 32-BIT, 333 MHz, RISC PROCESSOR, CBGA360
相關代理商/技術參數
參數描述
IBM25PPC750GXECB2563T 制造商:IBM 功能描述:
IBM25PPC750GXECB2H33T 制造商:IBM 功能描述:
IBM25PPC750GXECB5H42V 制造商:IBM 功能描述:POLARIS 1.2 ? 21CBGA GRE2 ? HALFMODE 933MH - Trays
IBM25PPC750GXECB5H82T 制造商:IBM 功能描述:POLARIS 1.2 ? 21CBGA GRE2 LP HALFMODE 933 - Trays
IBM25PPC750GXECB5H82V 制造商:IBM 功能描述:POLARIS 1.2 ? 21CBGA GRE2 LP HALFMODE 933 - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*