- 您現在的位置：買賣IC網 > PDF目錄379201 > IA2910A-PDW40C (Innovasic Semiconductor) Microprogram Controller PDF資料下載
參數資料
| 型號： | IA2910A-PDW40C |
| 廠商： | Innovasic Semiconductor |
| 英文描述： | Microprogram Controller |
| 中文描述： | 微程序控制器 |
| 文件頁數： | 6/19頁 |
| 文件大?。?/td> | 162K |
| 代理商： | IA2910A-PDW40C |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
Page 6 of 19
I
A2910A
Microprogram Controller
either identical to the YOUT output, or else one greater, as determined by CIn. For each
instruction, one and only one of the three outputs PLn, MAPn, and VECTn is LOW. If these
outputs control three-state enables for the primary source of microprogram jumps (usually part of a
pipeline register), a PROM which maps the instruction to a microinstruction starting location, and
an optional third source (often a vector from a DMA or interrupt source), respectively, the three-
state sources can drive the DIN inputs without further logic.
Preliminary
Data Sheet
Copyright
1999, InnovASIC Inc.
Customer SpecficIC Soutions
Several inputs, as shown in Table 2, can modify instruction execution. The combination CCn
HIGH and CCENn LOW is used as a test in 9 of the 16 instructions. RLDn, when LOW, causes
the DIN input to be loaded into the register/counter, overriding any HOLD or DEC operation
specified in the instruction. OEn, normally LOW, may be forced HIGH to remove the IA2910A
YOUT outputs from a three-state bus.
The stack, a nine-word last-in, first-out 12-bit memory, has a pointer which addresses the value
presently on the top of the stack. Explicit control of the stack pointer occurs during instruction 0
(RESET), which makes the stack empty by resetting the SP to zero. After a RESET, and
whenever else the stack is empty, the contents of the top of stack is undefined until a PUSH occurs.
Any POPs performed while the stack is empty put undefined data on the F outputs and leave the
stack pointer at zero.
Any time the stack is full (nine more PUSHes than POPs have occurred since the stack was last
empty), the FULLn warning output occurs. This signal first appears on the microcycle after a ninth
PUSH. No additional PUSH should be attempted onto a full stack; if tried, information within the
stack will be overwritten and lost.
相關PDF資料 |
PDF描述 |
|---|---|
| IA2910A-PDW40I | Microprogram Controller |
| IA2910A-PLC44C | Microprogram Controller |
| IA2910A-PLC44I | Microprogram Controller |
| IA8044 | SDLC COMMUNICATIONS CONTROLLER |
| IA8044-PDW40I-01 | SDLC COMMUNICATIONS CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IA2910A-PDW40I | 制造商:INNOVASIC 制造商全稱:INNOVASIC 功能描述:Microprogram Controller |
| IA2910A-PLC44C | 制造商:INNOVASIC 制造商全稱:INNOVASIC 功能描述:Microprogram Controller |
| IA2910A-PLC44I | 制造商:INNOVASIC 制造商全稱:INNOVASIC 功能描述:Microprogram Controller |
| IA294 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| IA296 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ULTRA LOW NOISE TRUE INSTRUMENTATION MEDICAL ISOLATION AMPLIFER |
發布緊急采購，3分鐘左右您將得到回復。