- 您現在的位置：買賣IC網 > PDF目錄260752 > HS45F-118-SS-1024-ABZC-28V/OC-D-M18 ROTARY OPTICAL POSITION ENCODER PDF資料下載
參數資料
| 型號： | HS45F-118-SS-1024-ABZC-28V/OC-D-M18 |
| 元件分類： | 編、解碼器及復用、解復用 |
| 英文描述： | ROTARY OPTICAL POSITION ENCODER |
| 文件頁數： | 2/2頁 |
| 文件大?。?/td> | 488K |
| 代理商： | HS45F-118-SS-1024-ABZC-28V/OC-D-M18 |
1. Mounting is usually done either using the D-style square flange mount, E- or G-style
servo mounts, or one of the standard face mounts, F1 for example. Consult factory for
additional face mount options.
2.The shaft seal is recommended in virtually all installations. The most common excep-
tions are applications requiring a very low starting torque or those requiring operation
at both high temperature and high speed.
3. Non-standard index widths and multiple indices are available by special order.
Consult factory.
4. Complementary outputs are recommended for use with line driver type (source/sink)
outputs. When used with differential receivers, this combination provides a high degree
of noise immunity.
5. Output IC’s: Output IC's are available as either Line Driver (LD) or NPN Open
Collector (OC) types. Open Collectors require pull-up resistors, resulting in higher out-
put source impedance (sink impedance is similar to that of line drivers). In general,
use of a Line Driver style output is recommended. Line Drivers source or sink current
and their lower impedance mean better noise immunity and faster switching times.
Warning: Do not connect any line driver outputs directly to circuit common/OV,
which may damage the driver. Unused outputs should be isolated and left floating.
Our applications specialists would be pleased to discuss your system requirements
and the compatibility of your receiving electronics with Line Driver type outputs.
28V/V: Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28
VDC +/- 5% standard (Note: Vout = Vin). This driver is TTL compatible when used
with 5 volt supply. Supply lines are protected against overvoltage to 60 volts and
reverse voltage. Outputs are short circuit protected for one minute. Supply current is
120 mA typical (plus load current). This is the recommended replacement for 3904R
and 7406R open collector outputs with internal pullup resistors. It is also a direct
replacement for any 4469, 88C30, 8830 or 26LS31 line driver
28V/5: Multi-voltage Line Driver (7272*): 100 mA source/sink. Input voltage 5 to 28
VDC +/- 5% standard, internally regulated with 5V (TTL compatible) logic out. Supply
lines are protected against overvoltage to 60 volts and reverse voltage. Outputs are short
circuit protected for one minute. Supply current is 90 mA typical (plus load current).
15V/V: Multi-voltage Line Driver (4469*): 100 mA source/sink. Input voltage 5 to 15
VDC +/- 5% standard (Note: Vout = Vin). TTL compatible when used with 5 volt sup-
ply. Supply lines are protected against overvoltage to 60 volts and reverse voltage.
Outputs are short circuit protected for one minute. Supply current is 90 mA typical
(plus load current). This is a direct replacement for the 4469 Line Driver.
28V/OC: NPN Open Collector (3904*, 7273*). Current sink of 80 mA max. Current
sourced by external pull- up resistor. Output can be pulled up to voltage other than
supply voltage (30 V max). Input voltage 5 to 28 VDC +/- 5% standard. Supply cur-
rent is 120 mA typical. This replaces prior IC's with designations of 3904, 7406,
3302, 681 and 689. 5V/OCR, 15V/OCR, 24V/OCR: Open Collector (3904R*,
7406R*, 7273R*): Current sink of 70 mA max. Includes internal pull-ups sized at
approximately 100 ohms/volt. Max current source is 10 mA. Supply current is 100
mA typical, 120 mA with internal pull-ups. The 5V/OCR, 15V/OCR and 24V/OCR are
often replaced by the 28V/V in system upgrades.
3904, 3904R, 4469, 5V/V, 5V/OC, 5V/OCR, 9V/OC: Intrinsically safe line driver and
open collector outputs. These drivers are specific to intrinsically safe encoders, and
are installed per the appropriate control drawings listed in Table 2.1 on page 48.
6. Special –S at the end of the model number is used to define a variety of non-stan-
dard features such as special shaft lengths, voltage options, or special testing. Please
consult the factory to discuss your special requirements.
7. Higher frequency response may be available. Please consult with the factory.
8. Extended temperature ratings are available in the following ranges:
-40 to 70°C, -40 to 85°C, –20 to 105°C and –40 to 105°C depending on the par-
ticular model. Some models can operate down to -55°C. Extended temperature
ranges can affect other performance factors. Consult with factory for more specific
information.
9. Mating straight plug receptacles may be ordered from the factory:
For M12 use MS3116F12-10S, For M14 use MS3106F14S-6S
For M14/19 use MS3116J14-19S, For M16 use MS3106F16S-1S
For M18 use MS3106F18-1S, For M20 use MS3106F20-29S
Dimensions
Figure 1 Output Waveform
Notes
Table 1 Incremental Output Terminations
M18 CONNECTOR
PIN
CHANNEL
AA
BB
CZ
D+V
E—
F0V
GCG
HA
IB
JZ
WIRE COLOR
DA 15P
CHANNELS DESIGNATED IN MODEL NO.
(22AWG)
CONNECTOR
ABZ
ABC
ABZC
YEL
13
A
BLUE
14
B
ORN
15
Z
—
Z
W-Yel
10
—
A
W-Blu
11
—
B
W-Orn
12
—
Z
RED
6
+V (SUPPLY VOLTAGE)
BLK
1
0 V (CIRCUIT COMMON)
GRN
9
CASE GROUND (CG) (except H20)
WHITE
SHIELD DRAIN (Shielded Cable Only)
* Products manufactured prior to April 2007 used the line driver IC number instead
of voltage output in model number.
HS45 Incremental Optical Encoder
BEI Industrial Encoders
HI
LO
CCW Rotation Viewing Face
The connector style will determine pinouts. For example, an encoder with ABC channels and an M18 con-
nector uses the table to the right.
CCW
4.68
#10-32x .32 (3)
ON A 4.00 B.C.
1.75 MAX
(1.625 MAX
W/ISOLATION
SLEEVE)
(R2.70)
(2.25)
(3.01)
CONNECTOR POSITIONS
FOR DUAL OUTPUT
MODEL (DM18)
OUTPUT 1
OUTPUT 2
CONNECTOR POSITION
FOR SINGLE OUTPUT
MODEL (SM18)
(R3.22)
(SLOT
BLOK)
3.25
1.74
0.38
0.86
2.75
(MAX)
3.15
0.98
MS3102R18-1P
CONNECTOR
.375
DOWEL PIN
2.93
GAP
(0.1)
TM
SLOT BLOK
R1 Tether Block and Pin
MS Connector Termination
3.63±0.03
3.17 thru
4.68
0.56 thru
1.01
R4.5
0.22
thru 12
places
R2 Tether Arm (Fits 7.25 [184] B.C.)
MAXIMUM BORE PENETRATION ON BLIND SHAFT IS 2.00"
Tel: 805-968-0782 /800-350-2727
Fax: 805-968-3154 / 800-960-2726
7230 Hollister Ave., Goleta, CA 93117-2807
www.beiied.com
HS45_Incremental_2008.qxp
7/11/08
9:22 AM
Page 2
相關PDF資料 |
PDF描述 |
|---|---|
| HS45F-125-BS-1000-ABZC-28V/OC-D-M18 | ROTARY OPTICAL POSITION ENCODER |
| HS45F-175-R2-BS-2500-ABZC-28V/V-D-M18 | ROTARY OPTICAL POSITION ENCODER |
| HS45F-175-R2-BS-720-ABZC-28V/V-S-M18 | ROTARY OPTICAL POSITION ENCODER |
| HS45F-175-SS-1000-ABZC-28V/OC-S-M18 | ROTARY OPTICAL POSITION ENCODER |
| HS45F-150-R1-BS-8192-ABZC-28V/OC-D-M18 | ROTARY OPTICAL POSITION ENCODER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HS-4-6 | 功能描述:HEX SPACER FOR #4 SCREW 3/4" RoHS:是 類別:硬件，緊固件，配件 >> 電路板襯墊，支座 系列:HS 標準包裝:100 系列:- 類型:圓形，無螺紋，母形/母形 尺寸:0.250"（6.35mm）1/4" 外徑 螺紋/螺釘/孔尺寸:#4，0.120"（3.05mm）內徑 長度 - 總體:1.000"（25.40mm） 材質:酚醛塑料 顏色:自然色 鍍層:- 板間高度:1.000"（25.40mm）1" 其它名稱:364K |
| HS-460 | 制造商:NEL 制造商全稱:Nel Frequency Controls,inc 功能描述:CRYSTAL CLOCK OSCILLATORS |
| HS-4610 | 制造商:BOSER 制造商全稱:BOSER 功能描述:VIA C7 or V4 Eden processor Embedded Engine Board w/CF |
| HS-4610C7 | 制造商:BOSER 制造商全稱:BOSER 功能描述:VIA C7 or V4 Eden processor Embedded Engine Board w/CF |
| HS-4610Eden | 制造商:BOSER 制造商全稱:BOSER 功能描述:VIA C7 or V4 Eden processor Embedded Engine Board w/CF |
發布緊急采購，3分鐘左右您將得到回復。