參數資料
型號： HPC46064
廠商： National Semiconductor Corporation
英文描述： High-Performance microController
中文描述： 高性能微控制器
文件頁數： 17/37頁
文件大小： 487K
代理商： HPC46064
HPC46064 Operating Modes
(Continued)
TL/DD/11372–15
FIGURE 17. 16-Bit External Memory
HPC46004 Operating Modes
EXPANDED ROMLESS MODE
Because the HPC46004 has no on-chip ROM, it has only
one mode of operation, the Expanded ROMless Mode. The
EXM pin must be pulled high (logic ‘‘1’’) on power up, the
EA bit in the PSW register should be set to a ‘‘1’’. The
HPC46004 is a ROMless device and is intended for use with
external memory. The external memory may be any combi-
nation of ROM and RAM. Up to 64k bytes of external mem-
ory may be accessed. It is necessary to vector on reset to
an address between C000 and FFFF, therefore the user
should have external memory at these addresses. The EA
bit in the PSW register must immediately be set to ‘‘1’’ at the
beginning of the user’s program to disable illegal address
detection in the WATCHDOG logic.
TABLE II. HPC46004 Operating Modes
Operating
Mode
EXM
Pin
EA
Bit
Memory
Configuration
Expanded ROMless
1
1
0300:FFFF off-chip
Note:
The on-chip RAM and Registers (0000:02FF) of the HPC46004 may
be accessed at all times.
Wait States
The internal ROM can be accessed at the maximum operat-
ing frequency with one wait state. With 0 wait states, internal
ROM accesses are limited to
)/3
f
C
max. The HPC46064
provides four software selectable Wait States that allow ac-
cess to slower memories. The Wait States are selected by
the state of two bits in the PSW register. Additionally, the
RDY input may be used to extend the instruction cycle, al-
lowing the user to interface with slow memories and periph-
erals.
Power Save Modes
Two power saving modes are available on the HPC46064:
HALT and IDLE. In the HALT mode, all processor activities
are stopped. In the IDLE mode, the on-board oscillator and
timer T0 are active but all other processor activities are
stopped. In either mode, all on-board RAM, registers and
I/O are unaffected.
HALT MODE
The HPC46064 is placed in the HALT mode under software
control by setting bits in the PSW. All processor activities,
including the clock and timers, are stopped. In the HALT
mode, power requirements for the HPC46064 are minimal
and the applied voltage (V
CC
) may be decreased without
altering the state of the machine. There are two ways of
exiting the HALT mode: via the RESET or the NMI. The
RESET input reinitializes the processor. Use of the NMI in-
put will generate a vectored interrupt and resume operation
from that point with no initialization. The HALT mode can be
enabled or disabled by means of a control register HALT
enable. To prevent accidental use of the HALT mode the
HALT enable register can be modified only once.
IDLE MODE
The HPC46064 is placed in the IDLE mode through the
PSW. In this mode, all processor activity, except the on-
board oscillator and Timer T0, is stopped. As with the HALT
mode, the processor is returned to full operation by the
RESET or NMI inputs, but without waiting for oscillator stabi-
lization. A timer T0 overflow will also cause the HPC46064
to resume normal operation.
17
相關PDF資料
PDF描述
HPC3130PBK PCI Bus Interface/Controller
HPC3130PBM PCI Bus Interface/Controller
HPC3130PGE PCI Bus Interface/Controller
HPC467064 High-Performance microController with a 16k UV Erasable CMOS EPROM
HPC467064EL20 High-Performance microController with a 16k UV Erasable CMOS EPROM
相關代理商/技術參數
參數描述
HPC46064XXX/T20 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller
HPC46064XXX/T30 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller
HPC46064XXX/U20 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller
HPC46064XXX/U30 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller
HPC46064XXX/V20 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*