參數資料
型號： HPC3130PGELOW-PROFILEQUAD
廠商： Texas Instruments, Inc.
英文描述： PCI HOT PLUG CONTROLLER
中文描述： 的PCI熱插拔控制器
文件頁數： 18/40頁
文件大?。?/td> 555K
代理商： HPC3130PGELOW-PROFILEQUAD
HPC3130
PCI HOT PLUG CONTROLLER
SCPS029B – DECEMBER1998
18
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
an acknowledge signal, indicating that it requires additional data, the HPC3130 continues to output data for each
received acknowledge signal. The master terminates the sequential read operation by not responding with an
acknowledge signal, and issues a STOP condition.
b7
S b6
b4
b5
b3 b2 b1 b0 0
b7 b6 b5 b4 b3 b2 b1 b0
A
A
Slave Address
Word Address
R/W
S/P = Start/stop condition
A = Slave acknowledgment
b6
b4
b5
b3 b2 b1 b0 1
A
Data Byte
M = Master acknowledgment
S
b6
b4
b5
b3 b2 b1 b0 M
P
Slave Address
R/W
Restart
Stop
Start
Figure 5. Serial Bus Protocol – Byte Read
parallel interface
The HPC3130 also implements an 8-bit parallel interface mode. When this mode is selected, the HPC3130
internal register addressed by the A[4:0] inputs can be accessed for a read/write transaction using the CS, RD,
WR strobes. The following signals have pullups on the mother board: IO16, M16, NOWS, CHRDY, MEMR,
MEMW, IOR, IOW, SD[15:0] to implement default states. Figure 6 shows write access using the default 8-bit
standard ISA bus cycle with four wait states. A read cycle is similar.
BCLK
CS
WR
A(0–4)
D(0–7)
Figure 6. Parallel Bus Write Cycle
connection sequencing
Before an add-in card is hot plugged and made available to the slot, the various pins in the HPC3130 have to
be controlled in a specific sequence. The HPC3130 provides the software interface to sequence the power to
the slot, clocks, and signals to the add-in cards that are being live inserted. The switch-timing block is used to
control the exact timing when the CBT switches are enabled.
The initial software sequencing is done by setting individual bits in the hot plug control register in the following
sequence. First, the SLTPWR_CTL bit is set high to drive the PWRON/OFF signal high. After the power to the
slot is applied, the SLOTRST_O bit is set low to drive the SLOTRST output. Next the CLKON_O bit is set low
to enable the PCI clock to the slot. Also, the REQ64_O bit is set to a value of 0 and the SLOTREQ64 bit is set
to indicate to the add-in card whether it is inserted into a 64-bit or 32-bit slot. SLOTREQ64 is set low for a 64-bit
slot and is set high for a 32-bit slot.
After initial software sequencing of the above signals is complete, the next step is to enable the CBT switches.
This can be done either by using the software to manually set the BUS_CTL bit or using the HPC3130 via the
automatic connection sequence mode located in the general configuration register.
相關PDF資料
PDF描述
HPC3130PBMQUADFLAT PCI HOT PLUG CONTROLLER
HPC3130PBKLOW-PROFILEQUAD PCI HOT PLUG CONTROLLER
HPC43100VHG30 16-Bit Microcontroller
HPC46003E20 16-Bit Microcontroller
HPC46003L20 16-Bit Microcontroller
相關代理商/技術參數
參數描述
HPC36003 制造商:NSC 制造商全稱:National Semiconductor 功能描述:High-Performance microControllers
HPC36003E30 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller
HPC36003L30 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller
HPC36003T30 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Microcontroller
HPC36003V20 功能描述:16位微控制器 - MCU RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*