參數資料
型號： HPC3130APGELOW-PROFILEQUA
廠商： Texas Instruments, Inc.
元件分類： 圓形連接器
英文描述： Circular Connector; No. of Contacts:79; Series:MS27656; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:21; Circular Contact Gender:Socket; Circular Shell Style:Wall Mount Receptacle RoHS Compliant: No
中文描述： 的PCI熱插拔控制器
文件頁數： 21/41頁
文件大?。?/td> 537K
代理商： HPC3130APGELOW-PROFILEQUA
HPC3130A
PCI HOT PLUG CONTROLLER
SCPS055 – NOVEMBER 1999
21
POST OFFICE BOX 655303
DALLAS, TEXAS 75265
connection sequencing (continued)
IDLEREQ, IDLEGNT, FRAME, and IRDY pins are not connected in manual mode. In contrast, during automatic
connection, the HPC3130A requests the PCIBus to make sure it is idle before it sequences through the
connection sequence.
In manual mode, software has to perform each part of the connection sequence. Figure 9 is an example of the
manual connection sequence. There could be several other ways to implement this protocol.
PCI_CLK
PWRON/OFF
PWRGOOD
SLOTRST
CLKON
REQ64ON
SLOTREQ64
BUS_CTL
BUSON
Figure 9. Manual Connection Sequencing
disconnecting sequence
The HPC3130A provides two mechanisms to isolate a PCI slot from the PCI bus so an add–in card can be
removed. One of the mechanisms is called manual sequencing and is enabled by default. This mechanism
allows the software to control the entire disconnect sequence. This means it is the software’s responsibility to
remove a powered slot from the PCI bus without any impact to the system.
The second mechanism is called autosequencing and can be enabled by programming either Auto-Sequence
1 or Auto-Sequence 2 in the general configuration register.Unlike the connection sequence, which has two
different autoconnection sequencing modes, the autodisconnect sequence has only one mode of operation.
The steps in the autodisconnect sequence are as follows:
1.
Software may assert SLOTRST to the appropriate slot by writing a 0 to the SLOTRST_O bit in the hot-plug
control register. This is optional.
2.
Next the software must set the BUS_CTL bit in the hot-plug control register to a 1.
3.
Once the BUS_CTL bit is set to a 1, the HPC3130A asserts IDLEREQ.
4.
Once IDLEGNT is asserted and FRAME and IRDY are deasserted, the HPC3130A deasserts BUSON and
CLKON and asserts REQ64ON to isolate the slot from the PCI bus.
5.
The HPC3130A then drives PWRON/OFF low to power off the slot.
相關PDF資料
PDF描述
HPC3130APBM PCI Bus Interface/Controller
HPC3130APBKLOW-PROFILEQUA DIODE ZENER DUAL COMMON-CATHODE 300mW 33Vz 5mA-Izt 0.0606 0.1uA-Ir 25 SOT-23 3K/REEL
HPC3130PGELOW-PROFILEQUAD PCI HOT PLUG CONTROLLER
HPC3130PBMQUADFLAT PCI HOT PLUG CONTROLLER
HPC3130PBKLOW-PROFILEQUAD PCI HOT PLUG CONTROLLER
相關代理商/技術參數
參數描述
HPC3130PBK 功能描述:外圍驅動器與原件 - PCI HOT PLUG CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
HPC3130PBKLOW-PROFILEQUAD 制造商:TI 制造商全稱:Texas Instruments 功能描述:PCI HOT PLUG CONTROLLER
HPC3130PBM 功能描述:外圍驅動器與原件 - PCI HOT PLUG CONTROLLER RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
HPC3130PBMQUADFLAT 制造商:TI 制造商全稱:Texas Instruments 功能描述:PCI HOT PLUG CONTROLLER
HPC3130PGE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Bus Interface/Controller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*