- 您現在的位置：買賣IC網 > PDF目錄367213 > HMC495LP3 (美國訊泰微波有限公司上海代表處) SiGe WIDEBAND DIRECT MODULATOR RFIC, 250 - 3800 MHz PDF資料下載
參數資料
| 型號： | HMC495LP3 |
| 廠商： | 美國訊泰微波有限公司上海代表處 |
| 英文描述： | SiGe WIDEBAND DIRECT MODULATOR RFIC, 250 - 3800 MHz |
| 中文描述： | 寬頻帶直接硅鍺射頻調制器，250 - 3800兆赫 |
| 文件頁數： | 9/12頁 |
| 文件大小： | 626K |
| 代理商： | HMC495LP3 |
M
8
8 - 10
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
Pin Number
Function
Description
Interface Schematic
1, 4, 9, 12
GND
These pins and the ground paddle must be connected to a
high quality RF/DC ground.
2, 3
LOP, LON
Differential LO input ports. This device may be driven in
either differential or single ended mode. In single ended
mode, one port should be driven by the LO source while
the other port may be terminated with a 50
Ω
resistor to
ground. An external shunt 68
Ω
resistor is used to improve
VSWR, while an external 100 pF capacitor is required
to prevent DC supply voltage from appearing on the
customer’s PC board.
5
VB2
Bias Voltage for the LO stage. This voltage will affect the
Sideband Suppression, the Output Noise Floor and the
Power Consumption. The ideal voltage range for this port
is between +2.7 Vdc and +3.0 Vdc. The nominal current for
this port is 5.3 mA.
6, 7
Qn, Qp
Differential Quadrature baseband input. These are
high impedance ports. The nominal recommended bias
voltage is between 1.0 - 1.15V. The nominal recommended
baseband input voltage is 800 mV peak to peak differential.
By adjusting the DC bias voltage on ports Qn & Qp, the
Carrier Suppression of the device can be optimized for a
specific frequency band and LO power level. The typical
offset voltage for optimization is less than 5 mV.
The amplitude and phase difference between the I and Q
inputs can be adjusted in order to optimize the Sideband
Suppression for a specific frequency band
and LO power level.
8
VB1
Bias Voltage for the output stage. This voltage should be
connected to the Vcc supply. Nominal supply voltage is 3.3
Vdc. The nominal current for this port is 2.4 mA.
10
N/C
No connect.
11
RFP
RF Output port. This port is matched to 50
Ω
. A series
capacitor should be connected to this port in order to
prevent the DC supply voltage from appearing on the
customer’s PC board.
Pin Descriptions
SiGe WIDEBAND DIRECT
MODULATOR RFIC, 250 - 3800 MHz
v02.0705
HMC495LP3
/
495LP3E
相關PDF資料 |
PDF描述 |
|---|---|
| HMC495LP3E | SiGe WIDEBAND DIRECT MODULATOR RFIC, 250 - 3800 MHz |
| HMC496LP3 | SiGe WIDEBAND DIRECT MODULATOR RFIC, 4.0 - 7.0 GHz |
| HMC496LP3E | SiGe WIDEBAND DIRECT MODULATOR RFIC, 4.0 - 7.0 GHz |
| HMC497LP4 | SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz |
| HMC497LP4E | SiGe WIDEBAND DIRECT MODULATOR RFIC, 100 - 4000 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC495LP3_08 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:SiGe WIDEBAND DIRECT MODULATOR RFIC, 250 - 3800 MHz |
| HMC495LP3E | 制造商:Hittite Microwave Corp 功能描述:IC MODULATOR SIGE DIRECT 16-QFN |
| HMC495LP3ETR | 制造商:Hittite Microwave Corp 功能描述:HMC495 Series 250-3800 Mhz 3.3 V 108 mA SiGe Direct Modulator - 3x3 mm QFN-16 |
| HMC496LP3 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:SiGe WIDEBAND DIRECT MODULATOR RFIC, 4.0 - 7.0 GHz |
| HMC496LP3_11 | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:SiGe WIDEBAND DIRECT MODULATOR RFIC, 4 - 7 GHz |
發布緊急采購，3分鐘左右您將得到回復。