- 您現在的位置：買賣IC網 > PDF目錄383073 > HMC103 SPST RF Absorptive Switch PDF資料下載
參數資料
| 型號： | HMC103 |
| 英文描述： | SPST RF Absorptive Switch |
| 中文描述： | 聚苯乙烯吸收射頻開關 |
| 文件頁數： | 10/15頁 |
| 文件大?。?/td> | 190K |
| 代理商： | HMC103 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁
HMC10XX FAMILY
10
Figure 9—Single Clock Set/Reset Circuit(1001/1002)
S/R strap @ 4.5
typ.
3A peak (min.)
10K
1
0.22μF
4.7μF (1)
+16 to 20V
17
HMC2003
Clock
S/R
(1) Tantalum, low R
0.022μF
0.022μF
10K
ZTX605
ZTX705
S/R strap @ 4.5
typ.
3A peak (min.)
10K
1
0.22μF
+16 to 20V
17
HMC2003
Clock
S/R
0.022μF
100K
ZTX605
Clock
S/R
-16V
T
PW
≈
2 μsec
5V
reset
Figure 10—Single Clock Reset Only Circuit (1001/1002)
Low Field Measurements—When measuring 100
μ
gauss
resolution or less, the permalloy film must be completely set,
or reset, to insure low noise and repeatable measurements.
A current pulse of 4 amps, or more, for just a couple
microseconds will ensure this. The circuits in Figures 7 and
8 are recommended for applications that require low noise
and high sensitivity magnetic readings.
Low Cost—For minimum field measurements above 500
μ
gauss, a less elaborate pulsing circuit can be used. In both
Figures 9 and 10, the pulse signal is switched using lower cost
Darlington transistors and fewer components. This circuit
may have a more limited temperature range depending on
the quality of transistors selected. If accuracy is not an issue
and cost is, then the reset only circuit in Figure 10 will work.
The circuit in Figure 12 generates a strong set/reset pulse
under a microprocessor clock driven control. A free running
555 timer can also be used to clock the circuit. The SET
current pulse is drawn from the 4.7
μ
F capacitor and a 200
ohm dropping resistor should be placed in series with the
supply to reduce noise.
Figure 11—5V Circuit for SET/RESET (1021/1022)
10K
0.1μF
1μF (1)
+5V
Clock
(1) Tantalum, low R
0.1μF
0.1μF
10K
FMMT617
FMMT717
200
9,15
14
HMC1022
8
For any magnetic sensor application, if temperature drift is
not an issue, then the reset pulse need only be occasionally
applied. This will save power and enable the use of digital
filtering techniques as shown in Figure 11. Circumstances
for a reset pulse would be 1) power on or, 2) field over/
under range condition. Any other time the sensor should
perform normally.
相關PDF資料 |
PDF描述 |
|---|---|
| HMC104 | SPDT RF Absorptive Switch |
| HMC105 | SPST RF Absorptive Switch |
| HMC106 | SPDT RF Reflective Switch |
| HMC109 | Analog Attenuator |
| HMC160QS16 | Interface IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HMC1030LP5E | 制造商:Hittite Microwave Corp 功能描述:RF DUAL RMS PWR DETECTOR 3.9GHZ |
| HMC1030LP5ETR | 功能描述:RF Detector IC General Purpose 0Hz ~ 3.9GHz -55dBm ~ 15dBm ±1dB 24-VFQFN Exposed Pad 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:停產 頻率:0Hz ~ 3.9GHz RF 類型:通用 輸入范圍:-55dBm ~ 15dBm 精度:±1dB 電壓 - 電源:4.5 V ~ 5.5 V 電流 - 電源:143mA 封裝/外殼:24-VFQFN 裸露焊盤 標準包裝:1 |
| HMC1031MS8E | 制造商:Hittite Microwave Corp 功能描述:IC CLOCK GEN INT-N PLL 8-MS8E |
| HMC1031MS8ETR | 功能描述:IC CLOCK GEN INT-N PLL 8-MS8E 制造商:analog devices inc. 系列:- 包裝:剪切帶（CT） 零件狀態:有效 類型:* PLL:是 輸入:時鐘 輸出:- 電路數:1 比率 - 輸入:輸出:1:1 差分 - 輸入:輸出:無/無 頻率 - 最大值:500MHz 分頻器/倍頻器:是/無 電壓 - 電源:2.7 V ~ 3.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商器件封裝:8-MS8E 標準包裝:1 |
| HMC1032LP6GE | 制造商:Hittite Microwave Corp 功能描述:IC CLOCK GEN 1:2 350MHZ 40-SMT |
發布緊急采購，3分鐘左右您將得到回復。